Lỗi máy CNC Mazak – Lỗi PLC mazak – Mazak PLC Alarm List

Lỗi máy CNC Mazak – Lỗi PLC mazak – Mazak PLC Alarm List

Lỗi máy CNC Mazak – Lỗi PLC mazak – Mazak PLC Alarm List

Mazak PLC Alarm List

  • 200 THERMAL TRIP (EMERGENCY STOP)
  • 201 BREAKER TRIP
  • 202 HYDRAULIC PRESSURE DOWN
  • 203 AIR PRESSURE DOWN
  • 204 SPINDLE CONTROLLER MALFUNCTION
  • 205 MILLING CONTROLLER MALFUNCTION
  • 206 OPEN FRONT DOOR (EMERGENCY STOP)
  • 211 NOT OPERATED MCODE SIMULTA.
  • 212 CHUCK OPEN/CLOSE SWITCH MALF.
  • 213 ILLEGAL DESIGNATED TOOL No.
  • 215 CHUCK SYSTEM MALFUNCTION
  • 218 CHUCKING TYPE NOT SELECTED
  • 220 TURRET POSITION SENSOR MALF.
  • 221 TURRET CLAMP SENSOR MALFUNCTION
  • 224 CHUCK SENSOR MALFUNCTION
  • 225 FRONT DOOR SENSOR MALFUNCTION
  • 231 TOOL EYE POSITION SENSOR MALF.
  • 234 TOOL CLAMP SENSOR MALFUNCTION
  • 236 PARTS-CATCHER SENSOR MALF.
  • 243 MEASURING CONTROLLER MALF.
  • 245 BAR-FEEDER CONTROLLER MALF.
  • 248 EXTERNAL CONTROLLER (No.1) MALF.
  • 250 SPINDLE START MISOPERATION
  • 251 MILLING MOTOR ROTATION PROHIB.
  • 252 AXIS MOVE MISOPERATION
  • 253 OVERLOAD DETECTION
  • 256 TURRET ROTATION PROHIBITED
  • 257 ILLEGAL M-CODE
  • 258 TNo. MISMATCH
  • 259 MODE CHANGE IMPOSSIBLE
  • 260 SLIDEWAY LUBRICATION ALARM
  • 261 HEAD LUBRICATION ALARM
  • 264 THERMAL TRIP X5 (SINGLE BLOCK)
  • 267 BALL SCREW X44C LUBRICATION ALARM
  • 270 SPINDLE ORIENT EXCEED TIME
  • 272 TURRET INDEX EXCEED TIME
  • 275 ROBOT SERVICE EXCEED TIME
  • 276 ATC CYCLE EXCEED TIME
  • 279 PARTS CATCHER CYCLE EXCEED TIME
  • 282 CHUCK CLAMP EXCEED TIME
  • 286 FRONT DOOR EXCEED TIME
  • 292 SENSOR MALFUNCTION No. 3
  • 293 SENSOR MALFUNCTION No. 4
  • 297 CHUCK PRESSURE DOWN
  • 300 START COND. ERR. (DOOR OPEN)
  • 301 START COND. ERR. (TUR UNCLAMP)
  • 302 START COND. ERR. (EXT RESET)
  • 303 START COND. ERR. (EXT FEED HOLD)
  • 308 C/S ERROR (TOOL EYE EXTEND)
  • 310 C/S ERROR (TNo.MISMATCH)
  • 311 C/S ERROR (TAIL STOCK QUILL)
  • 312 C/S ERROR (PTCATCHER EXTEND)
  • 313 C/S ERROR (C/S QUILL COMMAND)
  • 320 TOOL UNCLAMP IMP. (M-SP ROT.)
  • 321 MODE CHANGE IMPOSSIBLE (DURING ATC CYCLE)
  • 322 RAPID MODE IMP. (ORIGIN RET UNF)
  • 324 DIFF. MODE (ORIGIN RET UNFIN.)
  • 325 TL. EYE EXT. IMP.
  • 326 T/S QUILL EXT. IMP.
  • 327 NOT IN ATC START POSITION
  • 329 CHUCKING SELECTION PROHIBITED
  • 340 CONDITION No.1 MISSING
  • 341 CONDITION No.2 MISSING
  • 361 TAIL ALARM
  • 365 CARRIER CONTROLER MALFUNCTION
  • 366 SHIFTER CONTROLER MALFUNCTION
  • 374 OPERATING SWITCH FAULT
  • 375 MOTOR & SERVO TURNING OFF ERR.
  • 376 MAIN POWER TURNING OFF MALFUNCTION
  • 377 COOLANT LEVEL LOW
  • 378 HIGH PRESSURE PUMP THERMAL TRIP
  • 379 TANK PRESSURE LOW
  • 381 CONDITION MISSING (SET UP SWITCH)
  • 382 COOLANT SYSTEM MALF.
  • 383 ATC ALM: CARRIER&SHIFT. POS. MALF.
  • 385 START COND. ERR. (Z-AXIS POS.)
  • 386 ATC STOP
  • 390 TOOL ON INTERFER ALARM
  • 391 LD/ULD/ACHG CONDITION ALARM
  • 392 MAGAZINE MANUAL INTERR.
  • 394 ATC CONTROLLER MALF.
  • 395 CHECK SENSOR MALF. (SEE D199)
  • 397 MAGAZINE DOOR INTERLOCK
  • 398 MAGAZINE COVER OPEN
  • 399 MAINTE./ADJUST PARAM. ON

Lỗi máy CNC Mazak – Lỗi PLC mazak – Mazak PLC Alarm List

Trả lời

Email của bạn sẽ không được hiển thị công khai. Các trường bắt buộc được đánh dấu *

Contact Me on Zalo