Lỗi trên bộ điều khiển Fanuc 21i

Lỗi trên bộ điều khiển Fanuc 21i Fanuc 21i Alarms

Program errors (P/S alarm)

Lỗi trên bộ điều khiển Fanuc 21i Program errors /Alarms on program and operation (P/S alarm)

0 PLEASE TURN OFF POWER

1 TH PARITY ALARM

2 TV PARITY ALARM

3 TOO MANY DIGITS

4 ADDRESS NOT FOUND

5 NO DATA AFTER ADDRESS

6 ILLEGAL USE OF NEGATIVE SIGN

7 ILLEGAL USE OF DECIMAL POINT

9 ILLEGAL ADDRESS INPUT

10 IMPROPER G–CODE

11 NO FEEDRATE COMMANDED

14 CAN NOT COMMAND G95 (M series)

14 ILLEGAL LEAD COMMAND (T series)

15 TOO MANY AXES COMMANDED (M series)

15 TOO MANY AXES COMMANDED (T series)

20 OVER TOLERANCE OF RADIUS

21 ILLEGAL PLANE AXIS COMMANDED

22 NO CIRCLE RADIUS

23 ILLEGAL RADIUS COMMAND (T series)

25 CANNOT COMMAND F0 IN G02/G03 (M series)

27 NO AXES COMMANDED IN G43/G44 (M series)

28 ILLEGAL PLANE SELECT

29 ILLEGAL OFFSET VALUE (M series)

29 ILLEGAL OFFSET VALUE (T series)

30 ILLEGAL OFFSET NUMBER (M series)

30 ILLEGAL OFFSET NUMBER (T series)

31 ILLEGAL P COMMAND IN G10

32 ILLEGAL OFFSET VALUE IN G10

33 NO SOLUTION AT CRC (M series)

33 NO SOLUTION AT CRC (T series)

34 NO CIRC ALLOWED IN ST–UP /EXT BLK (M series)

34 NO CIRC ALLOWED IN ST–UP /EXT BLK (T series)

35 CAN NOT COMMANDED G39 (M series)

35 CAN NOT COMMANDED G31 (T series)

36 CAN NOT COMMANDED G31 (M series)

37 CAN NOT CHANGE PLANE IN CRC (M seires)

37 CAN NOT CHANGE PLANE IN NRC (T seires)

38 INTERFERENCE IN CIRCULAR BLOCK (M seires)

38 INTERFERENCE IN CIRCULAR BLOCK (T series)

39 CHF/CNR NOT ALLOWED IN NRC (T series)

40 INTERFERENCE IN G90/G94 BLOCK (T series)

41 INTERFERENCE IN CRC (M seires)

41 INTERFERENCE IN NRC (T seires)

42 G45/G48 NOT ALLOWED IN CRC (M series)

44 G27–G30 NOT ALLOWED IN FIXED CYC (M series)

45 ADDRESS Q NOT FOUND (G73/G83) (M series)

46 ILLEGAL REFERENCE RETURN COMMAND

47 ILLEGAL AXIS SELECT

48 BASIC 3 AXIS NOT FOUND

50 CHF/CNR NOT ALLOWED IN THRD BLK (M series)

50 CHF/CNR NOT ALLOWED IN THRD BLK(T series)

51 MISSING MOVE AFTER CHF/CNR (M series)

51 MISSING MOVE AFTER CHF/CNR (T series)

52 CODE IS NOT G01 AFTER CHF/CNR (M series)

52 CODE IS NOT G01 AFTER CHF/CNR (T series)

53 TOO MANY ADDRESS COMMANDS (M series)

53 TOO MANY ADDRESS COMMANDS (T seires)

54 NO TAPER ALLOWED AFTER CHF/CNR (T series)

55 MISSING MOVE VALUE IN CHF/CNR (M series)

55 MISSING MOVE VALUE IN CHF/CNR (T series)

56 NO END POINT & ANGLE IN CHF/CNR (T series)

57 NO SOLUTION OF BLOCK END (T series)

58 END POINT NOT FOUND (M series)

58 END POINT NOT FOUND (T series)

59 PROGRAM NUMBER NOT FOUND

60 SEQUENCE NUMBER NOT FOUND

61 ADDRESS P/Q NOT FOUND IN G70–G73 (T series)

62 ILLEGAL COMMAND IN G71–G76 (T series)

63 SEQUENCE NUMBER NOT FOUND (T series)

64 SHAPE PROGRAM NOT MONOTONOUSLY (T series)

65 ILLEGAL COMMAND IN G71–G73 (T series)

66 IMPROPER G–CODE IN G71–G73 (T series)

67 CAN NOT ERROR IN MDI MODE (T series)

69 FORMAT ERROR IN G70–G73 (T series)

70 NO PROGRAM SPACE IN MEMORY

71 DATA NOT FOUND

72 TOO MANY PROGRAMS

73 PROGRAM NUMBER ALREADY IN

74 ILLEGAL PROGRAM NUMBER

75 PROTECT

76 ADDRESS P NOT DEFINED

77 SUB PROGRAM NESTING ERROR

78 NUMBER NOT FOUND

79 PROGRAM VERIFY ERROR

80 G37 ARRIVAL SIGNAL NOT ASSERTED (M series)

80 G37 ARRIVAL SIGNAL NOT ASSERTED (T series)

81 OFFSET NUMBER NOT FOUND IN G37 (M series)

81 OFFSET NUMBER NOT FOUND IN G37 (T series)

82 H–CODE NOT ALLOWED IN G37 (M series)

82 T–CODE NOT ALLOWED IN G37 (T series)

83 ILLEGAL AXIS COMMAND IN G37 (M series)

83 ILLEGAL AXIS COMMAND IN G37 (T series)

85 COMMUNICATION ERROR

86 DR SIGNAL OFF

87 BUFFER OVERFLOW

88 LAN FILE TRANS ERROR (CHANNEL–1)

89 LAN FILE TRANS ERROR (CHANNEL–2)

90 REFERENCE RETURN INCOMPLETE

91 REFERENCE RETURN INCOMPLETE

92 AXES NOT ON THE REFERENCE POINT

94 P TYPE NOT ALLOWED (COORD CHG)

95 P TYPE NOT ALLOWED (EXT OFS CHG)

96 P TYPE NOT ALLOWED (WRK OFS CHG)

97 P TYPE NOT ALLOWED (AUTO EXEC)

98 G28 FOUND IN SEQUENCE RETURN

99 MDI EXEC NOT ALLOWED AFT. SEARCH

100 PARAMETER WRITE ENABLE

101 PLEASE CLEAR MEMORY

109 FORMAT ERROR IN G08 (M series)

110 DATA OVERFLOW

111 CALCULATED DATA OVERFLOW

112 DIVIDED BY ZERO

113 IMPROPER COMMAND

114 FORMAT ERROR IN MACRO

115 ILLEGAL VARIABLE NUMBER

116 WRITE PROTECTED VARIABLE

118 PARENTHESIS NESTING ERROR

119 ILLEGAL ARGUMENT

122 FOUR FOLD MACRO MODAL–CALL

123 CAN NOT USE MACRO COMMAND IN DNC

124 MISSING END STATEMENT

125 FORMAT ERROR IN MACRO

126 ILLEGAL LOOP NUMBER

127 NC, MACRO STATEMENT IN SAME BLOCK

128 ILLEGAL MACRO SEQUENCE NUMBER

129 ILLEGAL ARGUMENT ADDRESS

130 ILLEGAL AXIS OPERATION

131 TOO MANY EXTERNAL ALARM MESSAGES

132 ALARM NUMBER NOT FOUND

133 ILLEGAL DATA IN EXT. ALARM MSG

135 ILLEGAL ANGLE COMMAND (M series)

135 SPINDLE ORIENTATION PLEASE (T series)

136 ILLEGAL AXIS COMMAND (M series)

136 C/H–CODE & MOVE CMD IN SAME BLK. (T series)

137 M–CODE & MOVE CMD IN SAME BLK.

138 SUPERIMPOSED DATA OVERFLOW

139 CAN NOT CHANGE PMC CONTROL AXIS

141 CAN NOT COMMAND G51 IN CRC (M series)

142 ILLEGAL SCALE RATE (M series)

143 SCALED MOTION DATA OVERFLOW (M series)

144 ILLEGAL PLANE SELECTED (M series)

145 ILLEGAL CONDITIONS IN POLAR COORDINATE INTERPOLATION

146 IMPROPER G CODE

148 ILLEGAL SETTING DATA (M series)

149 FORMAT ERROR IN G10L3 (M series)

150 ILLEGAL TOOL GROUP NUMBER

151 TOOL GROUP NUMBER NOT FOUND

152 NO SPACE FOR TOOL ENTRY

153 T–CODE NOT FOUND

154 NOT USING TOOL IN LIFE GROUP (M series)

155 ILLEGAL T–CODE IN M06 (M series)

155 ILLEGAL T–CODE IN M06 (T series)

156 P/L COMMAND NOT FOUND

157 TOO MANY TOOL GROUPS

158 ILLEGAL TOOL LIFE DATA

159 TOOL DATA SETTING INCOMPLETE

160 MISMATCH WAITING M–CODE (T series (At two–path))

160 MISMATCH WAITING M–CODE (T series (At three–path))

160 G72.1 NESTING ERROR (M series))

161 ILLEGAL P OF WAITING M–CODE (T series (three–path control)

161 G72.1 NESTING ERROR (M series)

163 COMMAND G68/G69 INDEPENDENTLY T series (At two–path)

169 ILLEGAL TOOL GEOMETRY DATA (At two–path)

175 ILLEGAL G107 COMMAND

176 IMPROPER G–CODE IN G107 (M series)

176 IMPROPER G–CODE IN G107 (T series)

177 CHECK SUM ERROR (G05 MODE)

178 G05 COMMANDED IN G41/G42 MODE

179 PARAM. (NO. 7510) SETTING ERROR

180 COMMUNICATION ERROR (REMOTE BUF)

181 FORMAT ERROR IN G81 BLOCK (Hobbing machine, EGB) (M series)

182 G81 NOT COMMANDED (Hobbing machine) (M series)

183 DUPLICATE G83 (COMMANDS) (Hobbing machine) (M series)

184 ILLEGAL COMMAND IN G81 (Hobbing machine, EGB) (M series)

185 RETURN TO REFERENCE POINT (Hobbing machine) (M series)

186 PARAMETER SETTING ERROR (Hobbing machine, EGB) (M series)

190 ILLEGAL AXIS SELECT (M series)

194 SPINDLE COMMAND IN SYNCHRO–MODE

197 C–AXIS COMMANDED IN SPINDLE MODE

199 MACRO WORD UNDEFINED

200 ILLEGAL S CODE COMMAND

201 FEEDRATE NOT FOUND IN RIGID TAP

202 POSITION LSI OVERFLOW

203 PROGRAM MISS AT RIGID TAPPING

204 ILLEGAL AXIS OPERATION

205 RIGID MODE DI SIGNAL OFF

206 CAN NOT CHANGE PLANE (RIGID TAP) (M series)

207 RIGID DATA MISMATCH

210 CAN NOT COMAND M198/M199

211 G31 (HIGH) NOT ALLOWED IN G99

212 ILLEGAL PLANE SELECT (M series)

212 ILLEGAL PLANE SELECT (T series)

213 ILLEGAL COMMAND IN SYNCHRO–MODE

213 ILLEGAL COMMAND IN SYNCHRO–MODE (T series)

214 ILLEGAL COMMAND IN SYNCHRO–MODE

217 DUPLICATE G51.2 (COMMANDS) (T series)

218 NOT FOUND P/Q COMMAND IN G251 (T series)

219 COMMAND G250/G251 INDEPENDENTLY (T series)

220 ILLEGAL COMMAND IN SYNCHR–MODE (T series)

221 ILLEGAL COMMAND IN SYNCHR–MODE (T series)

222 DNC OP. NOT ALLOWED IN BG.–EDIT (M series)

224 RETURN TO REFERENCE POINT (M series)

224 RETURN TO REFERENCE POINT (T series)

225 SYNCHRONOUS/MIXED CONTROL ERROR (T series (At two–path))

226 ILLEGAL COMMAND IN SYNCHRO– MODE (T series (At two–path))

229 CAN NOT KEEP SYNCHRO–STATE (T series)

230 R CODE NOT FOUND (Grinding machine) (M series)

231 ILLEGAL FORMAT IN G10 OR L50

232 TOO MANY HELICAL AXIS COMMANDS (M series)

233 DEVICE BUSY

239 BP/S ALARM

240 BP/S ALARM

241 ILLEGAL FORMAT IN G02.2/G03.2 (M series)

242 ILLEGAL COMMAND IN G02.2/G03.2 (M series)

243 OVER TOLERANCE OF END POINT (M series)

244 P/S ALARM (T series)

245 T–CODE NOT ALOWEE IN THIS BLOCK (T series)

246 ENCODE PROGRAM NUMBER ERROR

247 ILLEGAL CODE USED FOR OUTPUT

250 Z AXIS WRONG COMMAND (ATC) (M series)

251 ATC ERROR (M series)

252 ATC SPINDLE ALARM (M series)

253 G05 IS NOT AVAILABLE (M series)

4500 REPOSITIONING INHIBITED

4502 ILLEGAL COMMAND IN BOLT HOLE

4503 ILLEGAL COMMAND IN LINE AT ANGLE

4504 ILLEGAL COMMAND IN ARC

4505 ILLEGAL COMMAND IN GRID

4506 ILLEGAL COMMAND IN SHARE PROOFS

4507 ILLEGAL COMMAND IN SQUARE

4508 ILLEGAL COMMAND IN RADIUS

4509 ILLEGAL COMMAND IN CUT AT ANGLE

4510 ILLEGAL COMMAND IN LINE-PUNCH

4511 ILLEGAL COMMAND IN CIRCLE-PUNCH

4520 T, M INHIBITED IN NIBBLING-MODE

4521 EXCESS NIBBLING MOVEMENT (X, Y)

4522 EXCESS NIBBLING MOVEMENT (C)

4523 ILLEGAL COMMAND IN CIRCLE-NIBBL

4524 ILLEGAL COMMAND IN LINE-NIBBL

4530 A/B MACRO NUMBER ERROR

4531 U/V MACRO FORMAT ERROR

4532 IMPROPER U/V MACRO NUMBER

4533 U/V MACRO MEMORY OVERFLOW

4534 W MACRO NUMBER NOT FOUND

4535 U/V MACRO NESTING ERROR

4536 NO W, Q COMMAND IN MULTI-PIECE

4537 ILLEGAL Q VALUE IN MULTI-PIECE

4538 W NO. NOT FOUND IN MULTI-PIECE

4539 MULTI-PIECE SETTING IS ZERO

4540 MULTI-PIECE COMMAND WITHIN MACRO

4542 MULTI-PIECE COMMAND ERROR

4543 MULTI-PIECE Q COMMAND ERROR

4544 MULTI-PIECE RESTART ERROR

4549 ILLEGAL TOOL DATA FORMAT

4600 T, C COMMAND IN INTERPOLATION

4601 INHIBITED T, M COMMAND

4602 ILLEGAL T-CODE

4603 C AXIS SYNCHRONOUS ERROR

4604 ILLEGAL AXIS OPERATION

4605 NEED ZRN

4630 ILLEGAL COMMAND IN LASER MODE

4650 IMPROPER G-CODE IN OFFSET MODE

4700 PROGRAM ERROR (OT +)

4701 PROGRAM ERROR (OT –)

4702 PROGRAM ERROR (OT +)

4703 PROGRAM ERROR (OT –)

4704 PROGRAM ERROR (OT +)

4705 PROGRAM ERROR (OT –)

5000 ILLEGAL COMMAND CODE (M series)

5003 ILLEGAL PARAMETER (HPCC) (M series)

5004 HPCC NOT READY

5006 TOO MANY WORD IN ONE BLOCK (M series)

5007 TOO LARGE DISTANCE (M series)

5009 PARAMETER ZERO (DRY RUN) (M series)

5010 END OF RECORD

5011 PARAMETER ZERO(CUT MAX) (M series)

5012 G05 P10000 ILLEGAL START UP (HPCC) (M series)

5013 HPCC: CRC OFS REMAIN AT CANCEL (M series)

5014 TRACE DATA NOT FOUND (M series)

5015 NO ROTATION AXIS (M series) (M series)

5016 ILLEGAL COMBINATION OF M CODE

5018 POLYGON SPINDLE SPEED ERROR (T series)

5020 PARAMETER OF RESTART ERROR

5030 ILLEGAL COMMAND (G100) (T series)

5031 ILLEGAL COMMAND (G100, G102, G103) (T series)

5032 NEW PRG REGISTERED IN B–AXS MOVE (T series)

5033 NO PROG SPACE IN MEMORY B–AXS (T series)

5034 PLURAL COMMAND IN G110 (T series)

5035 NO FEEDRATE COMMANDED B–AXS (T series)

5036 ADDRESS R NOT DEFINED IN G81–G86 (T series)

5037 ADDRESS Q NOT DEFINED IN G83 (T series)

5038 TOO MANY START M–CODE COMMAND (T series)

5039 START UNREGISTERED B–AXS PROG (T series)

5040 CAN NOT COMMANDED B–AXS MOVE (T series)

5041 CAN NOT COMMANDED G110 BLOCK (T series)

5043 TOO MANY G68 NESTING (M series)

5043 TOO MANY G68 NESTING (T series)

5044 G68 FORMAT ERROR (M series)

5044 G68 FORMAT ERROR (T series)

5046 ILLEGAL PARAMETER (ST.COMP)

5050 ILL–COMMAND IN CHOPPING MODE (M series)

5051 M–NET CODE ERROR

5052 M–NET ETX ERROR

5053 M–NET CONNECT ERROR

5054 M–NET RECEIVE ERROR

5055 M–NET PRT/FRT ERROR

5057 M–NET BOARD SYSTEM DOWN

5058 G35/G36 FORMAT ERROR (T series)

5059 RADIUS IS OUT OF RANGE (T series)

5060 ILLEGAL PARAMETER IN G02.3/G03.3 (M series)

5061 ILLEGAL FORMAT IN G02.3/G03.3 (M series)

5062 ILLEGAL COMMAND IN G02.3/G03.3

5063 IS NOT PRESET AFTER REF. (M series)

5064 DIFFERRENT AXIS UNIT (IS–B, IS–C)

5065 DIFFERENT AXIS UNIT (PMC AXIS) (M series)

5066 RESTART ILLEGAL SEQUENCE NUMBER (M series) (Fanuc 21i Model A)

5067 (HPCC) (M series)

5068 G31 FORMAT ERROR (M series)

5069 WHL–C:ILLEGA P–DATA (M series)

5073 NO DECIMAL POINT

5074 ADDRESS DUPLICATION ERROR

5082 DATA SERVER ERROR

5085 SMOOTH IPL ERROR 1

5096 MISMATCH WAITING M–CODE

5110 NOT STOP POSITION

5110 IMPROPER G–CODE (G05.1 G1 MODE) (M series) (Fanuc 21i Model A)

5111 IMPROPER MODAL G–CODE (G05.1 G1) (M series)

5111 IMPROPER MODEL G–CODE (G05.1 G1) (21i–M)

5112 G08 CAN NOT BE COMMANDED (G05.1 G1) (M series)

5112 G08 CAN NOT BE COMMANDED (G05.1 G1) (21i–M)

5113 CAN NOT ERROR IN MDI MODE (G05.1) (M series) (Fanuc 21i Model A)

5114 NOT STOP POSITION (G05.1 Q1) (M series)

5114 CAN NOT ERROR IN MDI MODE (G05.1) (21i–M)

5115 SPL : ERROR (M series)

5116 SPL : ERROR (M series)

5117 SPL : ERROR (M series)

5118 SPL : ERROR (M series)

5122 ILLEGAL COMMAND IN SPIRAL (M series)

5123 OVER TOLERANCE OF END POINT (M series)

5124 CAN NOT COMMAND SPIRAL (M series)

5134 FSSB : OPEN READY TIME OUT

5135 FSSB : ERROR MODE

5136 FSSB : NUMBER OF AMPS IS SMALL

5137 FSSB : CONFIGURATION ERROR

5138 FSSB : AXIS SETTING NOT COMPLETE

5139 FSSB : ERROR

5155 NOT RESTART PROGRAM BY G05

5156 ILLEGAL AXIS OPERATION (M series)

5157 PARAMETER ZERO (M series)

5195 DIRECTION CAN NOT BE JUDGED (T series)

5196 ILLEGAL OPERATION (HPCC) (M series)

5197 FSSB : OPEN TIME OUT

5198 FSSB : ID DATA NOT READ

5199 FINE TORQUE SENSING PARAMETER

5212 SCREEN COPY : PARAMETER ERROR

5213 SCREEN COPY : COMMUNICATION ERROR

5214 SCREEN COPY : DATA TRANSFER ERROR

5218 ILLEGAL PARAMETER (INCL. COMP)

5220 REFERENCE POINT ADJUSTMENT MODE

5222 SRAM CORRECTABLE ERROR

5227 FILE NOT FOUND

5228 SAME NAME USED

5229 WRITE PROTECTED

5231 TOO MANY FILES

5232 DATA OVER–FLOW

5235 COMMUNICATION ERROR

5237 READ ERROR

5238 WRITE ERROR

5242 ILLEGAL AXIS NUMBER (M series)

5243 DATA OUT OF RANGE (M series)

5244 TOO MANY DI ON (M series)

5245 OTHER AXIS ARE COMMANDED (M series)

5251 ILLEGAL PARAMETER IN G54.2 (M series)

5252 ILLEGAL P COMMAND IN G54.2 (M series)

5257 G41/G42 NOT ALLOWED IN MDI MODE (M series)

5303 TOUCH PANEL ERROR

5306 MODE CHANGE ERROR

5307 INTERNAL DATA OVER FLOW (M series)

5400 SPL:ILLEGAL AXIS COMMAND (M series)

5401 SPL:ILLEGAL COMMAND (M series)

5402 SPL:ILLEGAL AXIS MOVING (M series)

5403 SPL:CAN NOT MAKE VECTOR (M series)

5405 ILLEGAL PARAMETER IN G41.2/ G42.2 (M series)

5406 G41.3/G40 FORMAT ERROR (M series)

5407 ILLEGAL COMMAND IN G41.3 (M series)

5408 G41.3 ILLEGAL START_UP (M series)

5409 ILLEGAL PARAMETER IN G41.3 (M series)

5411 NURBS:ILLEGAL ORDER (M series)

5412 NURBS:NO KNOT COMMAND (M series)

5413 NURBS:ILLEGAL AXIS COMMAND (M series)

5414 NURBS:ILLEGAL KNOT (M series)

5415 NURBS:ILLEGAL CANCEL (M series)

5416 NURBS:ILLEGAL MODE (M series)

5417 NURBS:ILLEGAL MULTI–KNOT (M series)

5418 NURBS:ILLEGAL KNOT VALUE (M series)

5420 ILLEGAL PARAMETER IN G43.4/ G43.5 (M series)

5421 ILLEGAL COMMAND IN G43.4/ G43.5 (M series)

5422 EXCESS VELOCITY IN G43.4/ G43.5 (M series)

5425 ILLEGAL OFFSET VALUE (M series)

5430 ILLEGAL COMMAND IN 3–D CIR (M series)

5432 G02.4/G03.4 FORMAT ERROR (M series)

5433 MANUAL INTERVENTION IN 3–D CIR (M series)

5435 PARAMETER OUT OF RANGE (TLAC) (M series)

5436 PARAMETER SETTING ERROR 1 (TLAC) (M series)

5437 PARAMETER SETTING ERROR 2 (TLAC) (M series)

5440 ILLEGAL DRILLING AXIS SELECTED (M series)

5445 CRC:MOTION IN G39 (M series)

5446 CRC:NO AVOIDANCE (M series)

5447 CRC:DANGEROUS AVOIDANCE (M series)

5448 CRC:INTERFERENCE TO AVD. (M series)

5452 IMPROPER G–CODE (5AXIS MODE) (M series)

5453 NOTE: G68 IS CANCELED (HPCC) (M series)

5455 ILLEGAL ACC. PARAMETER (M series)

Lỗi trên bộ điều khiển Fanuc 21i Background edit alarm

BP/S alarm – BP/S alarm occurs in the same number as the P/S alarm that occurs in ordinary program edit. (070, 071, 072, 073, 074 085,086,087 etc.)

140 BP/S alarm

Lỗi trên bộ điều khiển Fanuc 21i Absolute pulse coder (APC) alarms

300 n AXIS NEED ZRN

301 APC ALARM:n AXIS COMMUNICATION

302 APC ALARM:n AXIS OVER TIME

303 APC ALARM:n AXIS FRAMING

304 APC ALARM:n AXIS PARITY

305 APC ALARM:n AXIS PULSE MISS

306 APC ALARM:n AXIS BATTERY ZERO

307 APC ALARM:n AXIS BATTERY DOWN 1

308 APC ALARM:n AXIS BATTERY DOWN 2

309 APC ALARM:n AXIS ZRN IMPOSSIBLE

Lỗi trên bộ điều khiển Fanuc 21i Serial pulse coder (SPC) alarms

360 n AXIS : ABNORMAL CHECKSUM (INT)

361 n AXIS : ABNORMAL PHASE DATA (INT)

362 n AXIS : ABNORMAL REV.DATA (INT)

363 n AXIS : ABNORMAL CLOCK (INT)

364 n AXIS : SOFT PHASE ALARM (INT)

365 n AXIS : BROKEN LED (INT)

366 n AXIS : PULSE MISS (INT)

367 n AXIS : COUNT MISS (INT)

368 n AXIS : SERIAL DATA ERROR (INT)

369 n AXIS : DATA TRANS. ERROR (INT)

380 n AXIS : BROKEN LED (EXT)

381 n AXIS : ABNORMAL PHASE (EXT LIN)

382 n AXIS : COUNT MISS (EXT)

383 n AXIS : PULSE MISS (EXT)

384 n AXIS : SOFT PHASE ALARM (EXT)

385 n AXIS : SERIAL DATA ERROR (EXT)

386 n AXIS : DATA TRANS. ERROR (EXT)

387 n AXIS : ABNORMAL ENCODER (EXT)

Lỗi trên bộ điều khiển Fanuc 21i Servo Alarms

401 SERVO ALARM: n–TH AXIS VRDY OFF

402 SERVO ALARM: SV CARD NOT EXIST

403 SERVO ALARM: CARD/SOFT MISMATCH

404 SERVO ALARM: n–TH AXIS VRDY ON

405 SERVO ALARM: (ZERO POINT RETURN FAULT)

407 SERVO ALARM: EXCESS ERROR

409 SERVO ALARM: n AXIS TORQUE ALM

410 SERVO ALARM: n–TH AXIS – EXCESS ERROR

411 SERVO ALARM: n–TH AXIS – EXCESS ERROR

413 SERVO ALARM: n–th AXIS – LSI OVERFLOW

415 SERVO ALARM: n–TH AXIS – EXCESS SHIFT

417 SERVO ALARM: n–TH AXIS – PARAMETER INCORRECT

420 SERVO ALARM: n AXIS SYNC TORQUE (M series)

421 SERVO ALARM: n AXIS EXCESS ER (D)

422 SERVO ALARM: n AXIS

423 SERVO ALARM: n AXIS

430 n AXIS : SV. MOTOR OVERHEAT

431 n AXIS : CNV. OVERLOAD

432 n AXIS : CNV. LOW VOLT CONTROL

433 n AXIS : CNV. LOW VOLT DC LINK

434 n AXIS : INV. LOW VOLT CONTROL

435 n AXIS : INV. LOW VOLT DC LINK

436 n AXIS : SOFTTHERMAL (OVC)

437 n AXIS : CNV. OVERCURRENT POWER

438 n AXIS : INV. ABNORMAL CURRENT

439 n AXIS : CNV. OVER VOLT DC LINK

440 n AXIS : CNV. EX DECELERATION POW.

441 n AXIS : ABNORMAL CURRENT OFFSET

442 n AXIS : CNV. CHARGE FAILURE

443 n AXIS : CNV. COOLING FAN FAILURE

444 n AXIS : INV. COOLING FAN FAILURE

445 n AXIS : SOFT DISCONNECT ALARM

446 n AXIS : HARD DISCONNECT ALARM

447 n AXIS : HARD DISCONNECT (EXT)

448 n AXIS : UNMATCHED FEEDBACK ALARM

449 n AXIS : INV. IPM ALARM

460 n AXIS : FSSB DISCONNECT

461 n AXIS : ILLEGAL AMP INTERFACE

462 n AXIS : SEND CNC DATA FAILED

463 n AXIS : SEND SLAVE DATA FAILED

464 n AXIS : WRITE ID DATA FAILED

465 n AXIS : READ ID DATA FAILED

466 n AXIS : MOTOR/AMP COMBINATION

467 n AXIS : ILLEGAL SETTING OF AXIS

Lỗi trên bộ điều khiển Fanuc 21i Over travel alarms

500 OVER TRAVEL : +n

501 OVER TRAVEL : –n

502 OVER TRAVEL : +n

503 OVER TRAVEL : –n

504 OVER TRAVEL : +n

505 OVER TRAVEL : –n

506 OVER TRAVEL : +n

507 OVER TRAVEL : –n

508 INTERFERENCE: +n (T series (two–path control))

509 INTERFERENCE: –n (T series (two–path control))

510 OVER TRAVEL: +n

511 OVER TRAVEL: –n

Lỗi trên bộ điều khiển Fanuc 21i Overheat alarms

700 OVERHEAT: CONTROL UNIT

701 OVERHEAT: FAN MOTOR

704 OVERHEAT: SPINDLE

Lỗi trên bộ điều khiển Fanuc 21i Rigid tapping alarms

740 RIGID TAP ALARM : EXCESS ERROR

741 RIGID TAP ALARM : EXCESS ERROR

742 RIGID TAP ALARM : LSI OVER FLOW

Lỗi trên bộ điều khiển Fanuc 21i Serial Spindle Alarms

749 S–SPINDLE LSI ERROR

750 SPINDLE SERIAL LINK START FAULT

752 FIRST SPINDLE MODE CHANGE FAULT

754 SPINDLE–1 ABNORMAL TORQUE ALM

762 SECOND SPINDLE MODE CHANGE FAULT

764 SPINDLE–2 ABNORMAL TORQUE ALM

772 SPINDLE–3 MODE CHANGE ERROR

774 SPINDLE–3 ABNORMAL TORQUE ALM

782 SPINDLE–4 MODE CHANGE ERROR

784 SPINDLE–4 ABNORMAL TORQUE ALM

Lỗi trên bộ điều khiển Fanuc 21i Safety zone alarms

4800 ZONE : PUNCHING INHIBITED 1

4801 ZONE : PUNCHING INHIBITED 2

4802 ZONE : PUNCHING INHIBITED 3

4803 ZONE : PUNCHING INHIBITED 4

4810 ZONE : ENTERING INHIBITED 1 +X

4811 ZONE : ENTERING INHIBITED 1 –X

4812 ZONE : ENTERING INHIBITED 2 +X

4813 ZONE : ENTERING INHIBITED 2 –X

4814 ZONE : ENTERING INHIBITED 3 +X

4815  ZONE : ENTERING INHIBITED 3 –X

4816 ZONE : ENTERING INHIBITED 4 +X

4817 ZONE : ENTERING INHIBITED 4 –X

4830 ZONE : ENTERING INHIBITED 1 +Y

4831 ZONE : ENTERING INHIBITED 1 –Y

4832 ZONE : ENTERING INHIBITED 2 +Y

4833 ZONE : ENTERING INHIBITED 2 –Y

4834 ZONE : ENTERING INHIBITED 3 +Y

4835 ZONE : ENTERING INHIBITED 3 –Y

4836 ZONE : ENTERING INHIBITED 4 +Y

4837 ZONE : ENTERING INHIBITED 4 –Y

4870 AUTO SETTING FEED ERROR

4871 AUTO SETTING PIECES ERROR

4872 AUTO SETTING COMMAND ERROR

Lỗi trên bộ điều khiển Fanuc 21i System Alarms

900 ROM PARITY

910 SRAM PARITY : (BYTE 0)

911 SRAM PARITY : (BYTE 1)

912 DRAM PARITY : (BYTE 0)

913 DRAM PARITY : (BYTE 1)

914 DRAM PARITY : (BYTE 2)

915 DRAM PARITY : (BYTE 3)

916 DRAM PARITY : (BYTE 4)

917 DRAM PARITY : (BYTE 5)

918 DRAM PARITY : (BYTE 6)

919 DRAM PARITY : (BYTE 7)

920 SERVO ALARM (1–4 AXIS)

921 SERVO ALARM (5–8 AXIS)

926 FSSB ALARM

930 CPU INTERRUPUT

935 SRAM ECC ERROR

950 PMC SYSTEM ALARM

951 PMC WATCH DOG ALARM

970 NMI OCCURRED IN PMCLSI

971 NMI OCCURRED IN SLC

972 NMI OCCURRED IN OTHER MODULE

973 NON MASK INTERRUPT

974 F–BUS ERROR

975 BUS ERROR

976 L–BUS ERROR

• Biến tần Yaskawa Nhật Bản
•     Robot công nghiệp

• >>>Robot lắp ráp- Assembly Robot
• >>>Robot gắp nhả – Handling Robot
• >>>Robot hợp tác – Coloborative Robot
• >>>Robot hàn-Welding Robot  Robot cắt -Cutting Robot
• >>>Robot sơn- Painting Robot
• >>>Robot Pallet – Palletizing Robot
• >>> Sản phẩm khác