Lỗi máy CNC Okuma

Lỗi máy CNC Okuma

Lỗi máy CNC Okuma Alarm P List

Sau đây là liệt kê danh sách Lỗi máy CNC Okuma Alarm P List

• 0700 NC start-up error
• 0701 P100-Menu initialization failure
• 0702 Power failure upon start-up
• 0703 Load information file not found
• 0704 File load error
• 0705 Default scheduling table error
• 0706 Backup data file error
• 0707 DTL link/unlink error
• 0708 RT thread stack overflow
• 0709 Hardware exception
• 0710 System call error
• 0711 AlarmService library error
• 0712 AlarmService internal error (exception)
• 0713 AlarmService error
• 0714 Blue screen
• 0715 P100-Menu error
• 0716 Floating point exception
• 0717 PLC control error
• 0718 Real time thread time over
• 0719 HXCP thread error
• 0720 AlarmService internal error
• 0721 DeviceNet error
• 0723 DeviceNet I/O data link file read
• 0725 M code data file
• 0726 Safety speed data error
• 0727 MCS firmware doesn’t support POS2 unit
• 0728 FL-net error
• 0729 Non-responsive software detected.
• 0731 R Spec. error
• 0732 Unable to execute lost motion compensation
• 0735 MCS DD encoder link error
• 0736 MCS DD encoder error
• 0737 MCS DD encoder (slave sensor) detected error
• 0738 MCS DD encoder initialization failure
• 0739 MCS DD encoder (slave sensor) initialization failure
• 0741 MCS firmware version error
• 0742 Relocation detection error
• 0744 MCS power supply unit overload
• 0750 The spec.-code or select-soft. was wrong
• 0752 VDU communication error
• 0753 VDU detected error
• 0754 VDU initialization failure
• 0755 SIO link error
• 0756 PSC optical scale encoder error
• 0757 MF-SAFETY Error
• 0758 Safety I/O Error
• 0759 Safety Servo Link Error
• 0782 Magnetic encoder speed detection error
• 0783 MCS Rotary encoder 5 initialization failure
• 0784 MCS Rotary encoder 5 error
• 0785 MCS Rotary encoder 4 initialization failure
• 0786 MCS Rotary encoder 4 error
• 0787 MCS Rotary encoder 3 initialization failure
• 0788 MCS Rotary encoder 3 error
• 0789 MCS Rotary encoder 2 error
• 0790 MCS Rotary encoder 1 initialization failure
• 0791 MCS Rotary encoder 1 error
• 0792 MCS Linear scale 4 initialization failure
• 0793 MCS Linear scale 4 error
• 0794 MCS Linear scale 3 initialization failure
• 0795 MCS Linear scale 3 error
• 0796 MCS Linear scale 2 initialization failure
• 0797 MCS Linear scale 2 error
• 0798 MCS Linear scale 1 initialization failure
• 0799 MCS Linear scale 1 error
• 0800 Spindle D/A control data file read
• 0801 TCP/IP board detected error
• 0802 Load information file not found
• 0803 File load error
• 0804 MSB file mismatch
• 0805 MOP-Tool parameter PBU load
• 0806 MOP-Tool tool data PBU load
• 0807 ACP panel status receipt error
• 0808 Speed change ratio failure
• 0810 NC I/O data file read
• 0812 MCS initialization error
• 0813 MCS Communication error
• 0814 MCS data file corrupt
• 0815 PLC real-time task loop error
• 0816 PLC initialization error
• 0817 MCS error
• 0818 ADP initialization failure
• 0820 Machine data file read
• 0821 Spindle gear ratio
• 0822 Wheel data file read
• 0823 AXIS CONSTRUCTION DATA setting error
• 0824 Unit connection mistake
• 0825 AXIS CONSTRUCTION name not set
• 0826 AXIS CONSTRUCTION DATA file read
• 0827 Control axis not found
• 0828 Wire feed axis No. error
• 0833 MCS option program file not sent
• 0834 MCS servo data error
• 0835 MCS communication error
• 0836 Program request illegal
• 0837 Loader spec. code data error
• 0838 Loader backup data file read error
• 0839 Specification conditions failure
• 0840 SuperHi-NC specification mismatch
• 0841 FCP4 board detected error
• 0842 Safety monitor spec. error
• 0845 Specification code setting failure
• 0846 Thermal deviation comp. backup data file read
• 0847 DNC-DT preload task start error
• 0848 PSCB error
• 0849 Synchronous axis tandem control initialization failure
• 0850 MCS Undefined alarm number
• 0851 MCS Inverter unit fault
• 0852 Mistake in data from MCS to NC
• 0853 MCS CON APA deviation
• 0854 MCS Power supply unit error
• 0855 MCS Converter link error
• 0856 MCS DC-bus voltage alarm
• 0857 MCS Motor overcurrent
• 0858 MCS Power unit overheat
• 0859 MCS Power unit overload
• 0860 MCS Supply voltage flutter
• 0861 MCS Inverter capacity differs from spec.
• 0862 MCS Winding change failure
• 0863 MCS Encoder link error
• 0864 MCS Encoder detected error
• 0865 MCS Encoder initialization failure
• 0866 MCS Encoder with shaft detected error
• 0867 MCS Encoder with shaft initialization failure
• 0868 MCS ABSO SCALE error
• 0869 MCS ABSO SCALE initialization failure
• 0870 MCS Magnetic encoder alarm
• 0871 MCS Resolver alarm
• 0872 MCS Pulse generator count over
• 0873 MCS Motor overheat
• 0874 MCS Servo link error
• 0875 MCS Servo link disconnection
• 0876 Mistake in data from NC to MCS
• 0877 MCS Servo data error
• 0878 MCS Illegal command
• 0879 MCS CON speed over
• 0880 MCS Speed command over
• 0881 MCS DIFF over
• 0882 MCS APA speed over
• 0883 MCS Full-closed APA error
• 0884 MCS Over speed
• 0885 MCS Speed deviation over
• 0886 MCS Collision detected
• 0887 MCS Urgent-stop time over
• 0888 MCS Belt is broken
• 0889 MCS Axis change control error
• 0890 MCS Independent encoder initialization failure
• 0891 MCS Calculated current position lies outside range
• 0892 MCS Motor overload
• 0893 MCS Safety speed monitor E-Link error
• 0894 MCS ABSO SCALE sub-slider detected error
• 0895 MCS Tandem control communication error
• 0896 MCS Full abso scale link error
• 0897 MCS Full abso scale error
• 0898 MCS Full abso scale initialization failure
• 0899 MCS Axis stop signal error
• 0940 Time sharing task control
• 0941 Real-time task control
• 0942 Real-time task loop error
• 0943 Main processor name incorrect
• 0944 Slave processor name incorrect
• 0945 Memory board/battery life
• 0951 SMP error
• 0952 Not equipped with processor board
• 0954 Peripheral processor start
• 0955 Spec. code: data file
• 0956 Backup data file read
• 0957 Graphic backup data file read
• 0958 Pitch compensation data file read
• 0965 Configuration file format error
• 0971 Cache data: Initialization error
• 0988 Cache data: Operation error
• 0989 CPU information table data incorrect
• 0990 TASK generate error
• 0991 TASK information table data incorrect
• 0992 PLC backup data file read
• 0993 TCP/IP board illegal
• 0994 TCP/IP configuration file
• 0995 Machine axis data file
• 0996 PLC axis data file
• 0997 PLC monitor backup data file read
• 0998 PLC sequence program load
• 0999 Synchronous tap data file read

Lỗi máy CNC Okuma Alarm A List

Below are  listed Okuma A type alarms for Okuma OSP-P300S/P300L CNC systems.

• 1071 Memory board battery depleted. Replace quickly!
• 1089 PLC alarm No. illegal
• 1091 PLC alarm message file not found
• 1092 PLC backup data file write
• 1093 PLC backup data file not found
• 1094 PLC back up data file read
• 1097 Safety speed monitor error
• 1098 MCS not responsive
• 1100 Parameters not set
• 1101 Blue screen
• 1102 P100-Menu error
• 1103 AlarmService internal error
• 1104 DeviceNet slave idle mode
• 1105 DTL error
• 1106 FL-net initialization error
• 1107 Major FL-net error
• 1108 Non-responsive software detected
• 1109 Error occurred during CAS
• 1110 PLC control error
• 1111 Shutting down to avoid damage
• 1112 Non-functioning device detected
• 1113 MCS Parameter learning error
• 1114 MCS Inertia identification error
• 1120 Overload detected.
• 1121 PSC Optical scale encoder error
• 1122 Safety controller error
• 1123 Safety speed monitor error
• 1132 VDU communication error
• 1133 VDU detected error
• 1134 VDU initialization failure
• 1135 MCS DD encoder link error
• 1136 MCS DD encoder error
• 1137 MCS DD Encoder (slave sensor) error
• 1138 MCS DD encoder initialization failure
• 1139 MCS DD encoder (slave sensor) initialization failure
• 1144 MCS Power supply unit overload
• 1146 Tailstock torque over
• 1150 MCS Undefined alarm number
• 1151 MCS Inverter unit fault
• 1152 Mistake in data from MCS to NC
• 1153 MCS CON APA deviation
• 1154 MCS Power supply unit error
• 1155 MCS Converter link error
• 1156 MCS DC-bus voltage alarm
• 1157 MCS Motor overcurrent
• 1158 MCS Power unit overheat
• 1159 MCS Power unit overload
• 1160 MCS Supply voltage flutter
• 1161 MCS Inverter capacity differs from spec.
• 1162 MCS Winding change failure
• 1163 MCS Encoder link error
• 1164 MCS Encoder detected error
• 1165 MCS Encoder initialization failure
• 1166 MCS Encoder with shaft detected error
• 1167 MCS Encoder with shaft initialization failure
• 1168 MCS ABSO SCALE error
• 1169 MCS ABSO SCALE initialization failure
• 1170 MCS Magnetic encoder alarm
• 1171 MCS Resolver alarm
• 1172 MCS Pulse generator count over
• 1173 MCS Motor overheat
• 1174 MCS Servo link error
• 1175 MCS Servo link disconnection
• 1176 Mistake in data from NC to MCS
• 1177 MCS Servo data error
• 1178 MCS Illegal command
• 1179 MCS CON speed over
• 1180 MCS Speed command over
• 1181 MCS DIFF over
• 1182 MCS APA speed over
• 1183 MCS Full-closed APA error
• 1184 MCS Over speed
• 1185 MCS Speed deviation over
• 1186 MCS Collision detected
• 1187 MCS Urgent-stop time over
• 1188 MCS Belt is broken
• 1189 MCS Axis change control error
• 1190 MCS Independent encoder initialization failure
• 1191 MCS Calculated current position lies outside range
• 1192 MCS Motor overload
• 1194 MCS ABSO SCALE sub-slider error
• 1195 MCS Tandem control communication error
• 1196 MCS Full abso scale link error
• 1197 MCS Full abso scale error
• 1198 MCS Full abso scale initialization failure
• 1199 MCS Axis stop signal error
• 1200 Stroke end over
• 1202 Plus variable limit over
• 1203 Minus variable limit over
• 1213 User reserve code
• 1215 S.M command asynchronous
• 1216 Synchronous P code error
• 1217 Torque limiter
• 1218 Torque limiter cancel
• 1219 Torque limit over
• 1220 Torque skip condition not satisfied
• 1221 Duplicate M-code
• 1222 Interrupt return pointer mismatch
• 1223 Thread feed command error
• 1225 Contour generation calculation error
• 1228 Illegal spindle mode
• 1229 Max. spindle rotation count not specified
• 1238 Spindle moved to interference distance
• 1243 Turret rotation conditions
• 1245 Axis moved to tool interference area
• 1257 Axis moved to chuck barrier area
• 1258 Axis moved to tailstock barrier area
• 1259 Tow-along tailstock connecting
• 1260 Tow-along tailstock command not possible
• 1262 W-axis plus variable limit over
• 1263 W-axis minus variable limit over
• 1265 Parts catcher interlock
• 1272 Load exceeds No.2 limit value
• 1273 Load monitor command already executed
• 1278 Laser measurement data NG
• 1279 IND. CMP. data verification failure
• 1280 HP9825A unable to receive
• 1281 Abnormal data from HP9825A
• 1282 Data error from HP9825A
• 1283 C-axis command not possible
• 1299 Axis moved to sub-spindle interference distance
• 1300 W-axis unable to move
• 1303 Pickoff index position
• 1306 Sensor touch G00
• 1307 No contact with sensor
• 1309 Sensor protect
• 1316 ATC manual operation mode impossible
• 1322 Y-axis parameter illegal
• 1323 Illegal YS-axis position
• 1328 Adaptive control communication error
• 1329 Shift amount error
• 1332 Spindle belt slip
• 1334 APA error
• 1336 Moved inside horizontal barrier area
• 1338 LOAD MONITOR W overload
• 1339 Spindle different from position when door open
• 1345 Unable to move to tool change position
• 1347 STM time over
• 1348 Cycle time over
• 1349 Contour generation impossible
• 1353 Measurement system error
• 1355 Tow-along steady rest connected
• 1356 Steady rest torque over
• 1357 Positioning uncertain
• 1367 NC tailstock position error
• 1376 Cutting error
• 1393 Tow-along steady rest interference position
• 1412 HOME POSITION movement interlock
• 1426 Moved inside barrier area
• 1431 Safety speed over
• 1432 Safety monitor error detection
• 1435 Turret interference
• 1436 Power ON APA deviation
• 1440 Steady rest-Tailstock interlock
• 1441 Safety speed clamp
• 1453 Heavy work data not found
• 1460 TEMP RISE LIMIT OVER
• 1463 Spindle moved inside transportation barrier
• 1465 Spindle low acceleration mode condition
• 1466 HOB cutting overload
• 1467 Position scale error XS-axis
• 1468 Servo amp error XS-axis
• 1469 APA speed XS-axis
• 1470 APA range XS-axis
• 1471 CON speed XS-axis
• 1472 Stroke end over XS-axis
• 1473 Actual position initialization error XS-axis
• 1474 Learning control error XS AXIS
• 1475 CAM execution data not selected XS-axis
• 1476 Learning control command XS-axis
• 1477 Syncronous mode command
• 1478 Chuck coordinates mismatch
• 1479 PSCB command error
• 1480 DIFF over XS-axis
• 1481 Drift compensation value over
• 1482 PSCB Real-time task error
• 1483 PSCB INT task loop error
• 1484 PSCB EC task loop error
• 1485 PSCB Time sharing task error
• 1486 PSCB Exception error
• 1487 PSCB Memory test error
• 1488 PSCB Overheat
• 1489 First time drift compensation value over
• 1490 Synchronous mode spindle speed command
• 1491 Heavy tooling data not found
• 1492 PSCB P.G. underpulse
• 1493 PSCB P.G. overpulse
• 1494 PSCB Minus stroke end over
• 1500 Workpiece rest interlock
• 1501 Workpiece rest torque over
• 1504 Alarm-A at other system
• 1507 Unable to enter C-axis sync. Mode
• 1509 A turret and B turret interference
• 1510 Unable to execute Hi-CUT Pro control
• 1511 SPM contour control not possible
• 1512 SPM contour control error
• 1513 Unable to clamp workpiece
• 1514 Clutch A slip over limit
• 1515 Mistake in X, Z commands
• 1516 NC tailstock slide resistance over
• 1517 Turret or tool not at index cut position
• 1519 Spindle phase over limit
• 1520 Synchronous error limit over
• 1521 NC tailstock error
• 1522 Linear guide cover interference area
• 1523 Workpiece weight data file not found
• 1524 Feed speed over
• 1525 M-tool spindle speed over in Hob mode
• 1526 Turret index error position
• 1527 Unable to execute while mounting LBB
• 1528 The attachment status mismatch
• 1529 M axis belt slip
• 1530 Steady-rests interference position
• 1531 Tool posture fluctuation reduction error
• 1532 Turret interference distance intrusion
• 1682 Magnetic encoder speed detection error
• 1683 MCS Rotary encoder 5 initialization failure
• 1684 MCS Rotary encoder 5 error
• 1685 MCS Rotary encoder 4 initialization failure
• 1686 MCS Rotary encoder 4 error
• 1687 MCS Rotary encoder 3 initialization failure
• 1688 MCS Rotary encoder 3 error
• 1689 MCS Rotary encoder 2 error
• 1690 MCS Rotary encoder 1 initialization failure
• 1691 MCS Rotary encoder 1 error
• 1692 MCS Linear scale 4 initialization failure
• 1693 MCS Linear scale 4 error
• 1694 MCS Linear scale 3 initialization failure
• 1695 MCS Linear scale 3 error
• 1696 MCS Linear scale 2 initialization failure
• 1697 MCS Linear scale 2 error
• 1698 MCS Linear scale 1 initialization failure
• 1699 MCS Linear scale 1 error
• 1700 Emergency stop
• 1701 EC overload
• 1702 BDU overload
• 1703 EC circuit breaker
• 1704 Transformer overheat
• 1705 Oil pressure low
• 1706 Alarm detected from externally connected device
• 1707 Stroke end over
• 1708 Canceling stroke end limit
• 1709 XA-axis overload
• 1710 XB-axis overload
• 1711 ZA-axis overload
• 1712 ZB-axis overload
• 1713 Spindle rotation interlock
• 1714 S.M command asynchronous
• 1715 Spindle revolution over
• 1716 M03/M04 change command failure
• 1717 Unable to use M40, M43, M44 commands
• 1718 Tow-along tailstock command error
• 1719 Gear command/position mismatch
• 1720 Gear command error
• 1721 Gear neutral
• 1722 M19 command issued when gear neutral
• 1723 Z-axis moved to spindle interference distance
• 1724 Spindle synchronization interlock
• 1725 Impossible command issued during spindle synchronization
• 1726 C-axis command not possible
• 1727 C-axis ON/OFF command not possible
• 1728 C-axis clamp/unclamp command not possible
• 1729 Unable to confirm C-axis advance
• 1730 Turret clamp/position check error
• 1731 Turret index control alarm
• 1732 Turret rotation interlock
• 1733 Tool number input error
• 1734 Pickoff chuck interlock
• 1735 Sub-spindle chuck pressure insufficient
• 1736 Pickoff index interlock
• 1737 Turret unclamp interlock
• 1738 Turret rotation impossible
• 1739 Chuck clamp pressure insufficient
• 1740 Chuck open/close interlock
• 1741 Chuck unclamp
• 1742 Chuck interlock cancel interlock
• 1743 Index chuck interlock
• 1744 Air chuck pressure error
• 1745 Chucking miss
• 1746 Chuck missclamp
• 1747 No tailstock quill advance answer
• 1748 Tailstock quill advance over
• 1749 Tailstock quill command error
• 1750 Tailstock interference
• 1751 Tow-along tailstock ON/OFF interlock
• 1752 Tow-along tailstock clamp/unclamp error
• 1753 Parts catcher interlock
• 1754 Coupling device alarm
• 1755 Robot inside machine
• 1756 Loader inside machine
• 1757 Loader interlock
• 1758 Loader not at escape position
• 1759 Loader/robot not at escape position
• 1760 Revolution tool M13/M14 change not possible
• 1761 Revolution tool gear mismatch
• 1762 Revolution tool gear interlock
• 1763 Tool revolution interlock
• 1764 Tool rotating when T command issued
• 1765 Rotation tool index interlock
• 1766 Rotation tool over speed
• 1767 M-axis clutch connection error
• 1768 Sub-spindle rotation over
• 1769 Sub-spindle index interlock
• 1770 Door interlock
• 1771 Door open/close limit switch NG
• 1772 Door open/close condition
• 1773 Unable to restore axis position when door closed
• 1774 Sensor head advance/retract interlock
• 1775 Touch setter limit
• 1776 Sensor head not at retract position
• 1777 ATC change arm position error
• 1778 No dummy tool in ATC turret
• 1779 Manual tool change operation interlock
• 1780 ATC system mode interlock
• 1781 Loader/robot interference
• 1782 Power sequence error
• 1783 Turret unclamp time over
• 1784 Turret clamp time over
• 1785 NC parameter data transfer error
• 1786 Coolant error
• 1787 Door open/close check NG
• 1788 Safety door open
• 1789 Steady rest interlock
• 1790 Bar feeder not ready
• 1791 Bar feeder advance/retract interlock
• 1792 Turret rotation interlock
• 1793 Side cover interlock
• 1794 Rear cover interlock
• 1795 Side cover open/close lmt switch NG
• 1796 Turret index clutch disconnect error
• 1797 Invalid mode switch
• 1798 Steady rest missclamp
• 1799 Sensor protection cover interlock
• 1800 Locking switch NG
• 1801 Bar feeder setting position mismatch
• 1802 Safety guard interlock
• 1803 Machine enabling button error
• 1804 Safety speed monitor output error
• 1805 Teaching panel enabling switch error
• 1806 ATC Logic data file error
• 1807 Shutter close not possible
• 1808 Safety fence locking switch NG
• 1809 Manual command time over
• 1810 Safety guard interlock
• 1811 Loader axis unable to move
• 1812 Mist lubrication unit error
• 1813 2nd spindle condition satisfy
• 1814 W-axis movement interlock
• 1815 Face driver pressure insufficient
• 1816 Safety fence open
• 1817 Setup switch ON
• 1818 Hand slide interlock
• 1819 Hand turning interlock
• 1820 Turnover interlock
• 1821 Magazine door lock error
• 1822 Slide step interlock
• 1823 Vibration cutter faulty
• 1824 Oil cooler error
• 1825 Spindle cooling unit error
• 1826 Oil air lubrication illegal
• 1827 Setup switch ON
• 1828 Laser sensor interlock
• 1829 Sp. oil air lub. air pressure error
• 1830 SP. oil air lub. oil level error
• 1831 Sp. oil air lub. oil pressure error
• 1832 Unloader advance/retract interlock
• 1833 Tow-along steady rest unclamp interlock
• 1834 Door interlock
• 1835 Workpiece receiver interlock
• 1836 Interference area intrusion
• 1837 Worktable overload
• 1838 Workpiece stabilizer interlock
• 1839 Deburring tool interlock
• 1840 M code data file mismatch
• 1841 Swing interlock
• 1842 Wrist rotation interlock
• 1843 Workpiece rest interlock
• 1844 Workpiece pusher interlock
• 1845 Hand rotation interlock
• 1846 Chuck grip confirmation unit faulty
• 1847 Tailstock air miss detection input NG
• 1848 Chuck grip failure
• 1849 Workpiece unloading unit interlock
• 1850 Robot/Loader emergency stop
• 1851 Air pressure insufficient
• 1852 NC alarm
• 1853 Oil pressure insufficient
• 1854 Error detected from externally connected device
• 1855 M code time over
• 1856 Circuit breaker tripped
• 1857 Intrusion interlock
• 1858 No hand open/close output
• 1859 Swing position no output
• 1860 Axis interlock
• 1861 Stroke end over
• 1862 Canceling stroke end limit
• 1863 Loader interference
• 1864 Z/C-axis not in rotation possible area
• 1865 Swing position indefinite
• 1866 No workpiece clamped on hand A
• 1867 No workpiece clamped on hand B
• 1868 Wrist broken
• 1869 Hand open/ close interlock
• 1870 Hand clamp confirmation
• 1871 Coupling device error
• 1872 Safety fence interlock
• 1873 Door interlock
• 1874 Interlock release NG
• 1875 Safety fence lock NG
• 1876 Swing interlock
• 1877 Robot/Loader power sequence error
• 1878 Machine start impossible
• 1879 Workpiece puller holder interlock
• 1880 Loader hand/machine interference
• 1881 Part turnover device R clamp empty
• 1882 Part turnover device L clamp empty
• 1883 Part turnover device R advanced too far
• 1884 Part turnover device L advanced too far
• 1885 Loader/part turnover device interference
• 1886 Wrist turning position indefinite
• 1887 Workpiece puller interlock
• 1888 Backup roller interlock
• 1889 Auto workpiece I/O unit FWD pressure low
• 1890 Coolant flow insufficient
• 1891 Unloader interference position
• 1892 Unloader interlock
• 1893 Running mode error
• 1894 Running mode error
• 1895 Fire alarm
• 1896 Air source pressure low
• 1897 Lower turret drive belt torn
• 1898 OP panel within interference range
• 1899 Safety fence open
• 1900 Plus variable limit over
• 1901 Minus variable limit over
• 1920 User reserve code
• 1922 Torque limit over
• 1924 Barrier intrusion
• 1927 M code time over
• 1928 Cycle time over
• 1938 Machine start impossible
• 1939 Hand open/close interlock
• 1940 Loader Z-axis stopper set
• 1941 Safety guard interlock
• 1942 Safety speed over
• 1943 Safety speed monitor error
• 1944 Safety monitor error detection
• 1945 Running mode error
• 1949 Alarm-A at other system
• 1950 Safety speed monitor error
• 1951 Safety controller error
• 8500 Cut off error
• 8501 ATC shutter not close
• 8502 Unable to G21
• 8503 Spindle internal centering unit interlock
• 8504 Tool change command
• 8505 Tow-along steady rest clamp/unclamp
• 8506 Combination chuck interlock
• 8507 Automatic lubrication system error
• 8508 Coolant filter
• 8509 Cutting feed interlock
• 8510 Oil unit error
• 8511 B-axis clamp/unclamp interlock
• 8512 Turret position uncertain
• 8513 Coolant interlock
• 8514 Work conveyor interlock
• 8515 Work ejector interlock
• 8516 Touch setter unlock time over
• 8517 Work hand interlock
• 8518 Bar Feeder illegal
• 8520 Stopper interlock
• 8521 Work measurement operation
• 8522 Locater oil pressure
• 8523 Locater condition
• 8524 Oil motor overload
• 8525 Coolant motor overload
• 8526 Spindle cooling motor overload
• 8527 Oil skimmer overload
• 8528 Magnet separator overload
• 8529 Tool monitoring unit error detection
• 8530 Laser sensor input data error
• 8531 Door open
• 8532 Polish Material unit interlock
• 8536 Operation ready OFF condition
• 8537 Magazine door Interlock
• 8538 ATC shutter barrier area
• 8539 Complete stop
• 8540 X-axis in interference range
• 8541 Spindle phase synchronization interlock
• 8542 Synchronizing spindle phase
• 8543 Measurement Unit error
• 8545 Illegal robot/loader request
• 8546 Rolling-head movement error
• 8547 Drive jig unit interlock
• 8548 ACC interlock
• 8549 ACC door interlock
• 8550 ACC manual operation mode impossible
• 8551 Semi-dry unit error
• 8552 Sub-chuck interlock
• 8553 ACC airblow interlock
• 8554 Spindle table rotation
• 8555 B-Axis movement
• 8556 No mount magazine
• 8557 Tool Breakage sensor error
• 8558 L-tool index command
• 8559 Part turn device advanced too far
• 8560 Override switch failure
• 8561 Grinding whl spindle motor overload
• 8562 Whl spdl coolant pressure drop/loss
• 8563 Inverter failure
• 8564 Turret drive belt disconnection
• 8566 Tool clamp interlock
• 8567 Spindle cover open/close limit SW NG
• 8568 Insulation error
• 8569 Magazine turn interlock
• 8570 Magazine tool No.
• 8571 Irregular coolant level
• 8572 ATC step time over
• 8573 Spingdle vibration
• 8574 MCS operation ready off
• 8575 Grinding whl spindle unit
• 8576 Grinding whl spindle unit interlock
• 8577 Axis interlock
• 8578 Coupling device interlock
• 8579 Tailstock and turret interference
• 8580 Canceling interference detection
• 8581 Loader automatic operation
• 8582 Illegal workpiece pusher confirmation
• 8583 ATC change arm overload
• 8584 Tailstock high/low change interlock
• 8585 Coiling prevention equip. interlock
• 8586 Air picker broken
• 8587 AREA SENSOR interlock
• 8588 Coolant Flow
• 8589 Chip conveyor faulty
• 8590 Tailstock pedestal condition
• 8591 C-axis synchronous condition
• 8592 Synchronizing C-axis
• 8593 Chip crusher error
• 8594 Sensor overstroke
• 8595 Linear guide cover interference
• 8596 Safety plug interlock
• 8597 Shuttle device hand clamp empty
• 8598 Ceiling door interlock
• 8599 Illegal tool clamp unit
• 8600 Ceiling door open/close limit SW NG
• 8601 ATC tool change arm inverter failure
• 8602 Chip pan cover interlock
• 8603 C-axis clamp/unclamp condition
• 8604 Long tool change protection
• 8605 Drive belt disconnection
• 8606 APC door open/close limit NG
• 8607 XB cover interference
• 8608 Illegal touch setter unit
• 8609 Axis overheat
• 8610 Invalid spindle winding condition
• 8611 Winding change error
• 8612 APC interlock
• 8613 APC clamp/unclamp time over
• 8614 APC escape position
• 8615 ATC shutter not open
• 8616 Coolant level low
• 8617 Thru-the-tool coolant filter clogged
• 8618 M spindle overload
• 8619 Machine axis travel limit over
• 8620 PLC system data
• 8621 M spindle air curtain pressure low
• 8622 Hydraulic unit oil level low
• 8623 Mist air lubrication unit
• 8624 Axis interlock
• 8625 Tool revolution command
• 8626 Ceiling door guide interlock
• 8627 Long boring bar change protection
• 8628 Spindlehead lib oil level low
• 8629 Spindlehead lubricant pressure low
• 8630 Hydraulic pressure drop
• 8631 Invalid safety-monitor spec.
• 8632 UNUSABLE interrupt program
• 8633 AAC Operation mode impossible
• 8634 ATC shutter open/close condition
• 8635 Spindle actual position detection error
• 8636 RSS unit Battery error
• 8637 RSS unit Communication error
• 8638 Sub-spindle head clamp condition
• 8639 Tailstock control mode ON/OFF cond.
• 8640 Center partition interlock
• 8643 Unusable PLC spec. code
• 8644 Fire extinguish unit power OFF
• 8645 Fire extinguish unit error
• 8646 Fire ext. unit power OFF or error
• 8647 Hand open/close switch NG
• 8648 Tailstock tool mode mismatch
• 8649 Measurement sensor unit interlock
• 8680 Area sensor interlock

Lỗi máy CNC Okuma Alarm B List

Sau đây là liệt kê danh sách Lỗi máy CNC Okuma Alarm B List  for Okuma OSP-P300S/P300L CNC systems.

• 2049 PLC axis stroke end over
• 2050 PLC axis command
• 2051 PLC axis continuous positioning over
• 2052 Blue screen
• 2053 P100-Menu error
• 2058 Error occurred while CAS work
• 2059 Non-functioning device detected
• 2060 Fan motor error on panel computer unit
• 2090 The remaining time after relocation has passed
• 2092 MCS Parameter learning error
• 2114 MCS Inertia identification error
• 2120 Overload detected.
• 2132 VDU communication error
• 2133 VDU detected error
• 2134 VDU initialization failure
• 2135 MCS DD encoder link error
• 2136 MCS DD Encoder error
• 2137 MCS DD Encoder (slave sensor) error
• 2138 MCS DD encoder initialization failure
• 2139 MCS DD encoder (slave sensor) initialization failure
• 2144 MCS Power supply unit overload
• 2150 MCS Undefined alarm number
• 2151 MCS Inverter unit fault
• 2152 Mistake in data from MCS to NC
• 2153 MCS CON APA deviation
• 2154 MCS Power supply unit error
• 2155 MCS Converter link error
• 2156 MCS DC-bus voltage alarm
• 2157 MCS Motor overcurrent
• 2158 MCS Power unit overheat
• 2159 MCS Power unit overload
• 2160 MCS Supply voltage flutter
• 2161 MCS Inverter capacity differs from spec.
• 2162 MCS Winding change failure
• 2163 MCS Encoder link error
• 2164 MCS Encoder detected error
• 2165 MCS Encoder initialization failure
• 2166 MCS Encoder with shaft detected error
• 2167 MCS Encoder with shaft initialization failure
• 2168 MCS ABSO SCALE error
• 2169 MCS ABSO SCALE initialization failure
• 2170 MCS Magnetic encoder alarm
• 2171 MCS Resolver alarm
• 2172 MCS Pulse generator count over
• 2173 MCS Motor overheat
• 2174 MCS Servo link error
• 2175 MCS Servo link disconnection
• 2176 Mistake in data from NC to MCS
• 2177 MCS Servo data error
• 2178 MCS Illegal command
• 2179 MCS CON speed over
• 2180 MCS Speed command over
• 2181 MCS DIFF over
• 2182 MCS APA speed over
• 2183 MCS Full-closed APA error
• 2184 MCS Over speed
• 2185 MCS Speed deviation over
• 2186 MCS Collision detected
• 2187 MCS Urgent-stop time over
• 2188 MCS Belt is broken
• 2189 MCS Axis change control error
• 2190 MCS Independent encoder initialization failure
• 2191 MCS Calculated current position lies outside range
• 2192 MCS Motor overload
• 2194 MCS ABSO SCALE sub-slider error
• 2195 MCS Tandem control communication error
• 2196 MCS Full abso scale link error
• 2197 MCS Full abso scale error
• 2198 MCS Full abso scale initialization failure
• 2199 MCS Axis stop signal error
• 2200 G-code error
• 2201 M-code error
• 2202 Common variable error
• 2203 System variable error
• 2204 Sequence name error
• 2205 Numeric data error
• 2206 Character use error
• 2207 Program name error
• 2208 Character string error
• 2209 Hexadecimal data error
• 2210 Spindle max revolution error
• 2212 G132/G133 command error
• 2213 Program factor over
• 2214 Subscript left side incorrect
• 2215 Local variable use over
• 2216 System variable setting data over
• 2217 Output variable setting data mistake
• 2218 UNUSABLE G-code
• 2219 UNUSABLE M-code
• 2220 Subscript left side illegal
• 2221 UNUSABLE output variable No
• 2222 UNUSABLE input variable No
• 2223 UNUSABLE turret direct code
• 2224 UNUSABLE contour generation command
• 2225 UNUSABLE Y-Z circle command
• 2226 UNUSABLE thread cutting command
• 2227 Mnemonic or local variable mistake
• 2228 VSET sequence left command mistake
• 2229 EXPRESSION right side
• 2230 EXPRESSION calculation error
• 2231 EXPRESSION syntax incorrect
• 2232 EXPRESSION subscript mistake
• 2233 EXPRESSION buffer over
• 2234 EXPRESSION local variable
• 2235 Equal does not exist
• 2236 Program end code not found
• 2237 BRANCH (IF,GOTO) sequence name
• 2238 BRANCH(IF,GOTO) condition
• 2239 Mistake in F command
• 2240 Mistake in F/E command
• 2241 Mistake in I command
• 2242 Mistake in J command
• 2243 Mistake in K command
• 2244 Mistake in L command
• 2245 Mistake in P command
• 2246 Mistake in S command
• 2247 No S command
• 2248 Mistake in T command
• 2249 Mistake in X command
• 2250 Mistake in X/Z command
• 2251 Mistake in Z command
• 2252 Mistake in arc command
• 2253 Mistake in angle command
• 2254 Mistake in thread cutting cycle command
• 2255 Mistake in arc radius command
• 2256 Mistake in D command
• 2257 Mistake in gauging cycle command
• 2258 Mistake in C command
• 2259 Mistake in SB command
• 2260 Mistake in QA command
• 2261 Mistake in X/Y command
• 2262 Mistake in incremental command
• 2263 Command required for X-, Y-axes
• 2264 Mistake in Y command
• 2265 Distance calculation over limit
• 2266 Mistake in R command
• 2267 Mistake in drilling cycle command
• 2268 Mistake in angle command
• 2269 Angle chamfering command error
• 2270 Mistake in CD command
• 2271 Mistake in CL command
• 2272 Mistake in TM command
• 2273 Mistake in W command
• 2274 Mistake in CB command
• 2275 Mistake in HP command
• 2276 Mistake in CC command
• 2277 Mistake in torque limit command
• 2278 SUB PROGRAM repetition
• 2279 SUB PROGRAM stack
• 2280 SUB PROGRAM program name
• 2281 SUB PROGRAM data print
• 2282 SCHEDULE PROGRAM ‘Q’
• 2283 SCHEDULE PROGRAM mnemonic code
• 2284 SCHEDULE PROGRAM program end
• 2285 SCHEDULE PROGRAM main program load
• 2286 Plus variable limit over
• 2287 Minus variable limit over
• 2288 User reserve code
• 2289 Unable to write backup data file
• 2290 Program name not selected
• 2291 Main sequence error
• 2292 Restart failure
• 2293 MDI special G-code
• 2294 Special G-code table
• 2295 STM time over
• 2296 UGC No program end code
• 2297 UGC DELETE syntax
• 2298 UGC DEF syntax
• 2299 UGC TIP syntax
• 2300 UGC TIF syntax
• 2301 UGC No shape entry
• 2302 UGC Illegal numerical data
• 2303 UGC Illegal character
• 2304 UGC User variable
• 2305 UGC System variable
• 2306 UGC Illegal command
• 2307 UGC Program factor over
• 2308 UGC Coordinate data
• 2309 UGC END syntax
• 2310 UGC Command over
• 2311 UGC Command format
• 2312 UGC Additional parameter
• 2313 UGC Expression
• 2314 UGC Figure entry area over
• 2315 UGC Unable to delete
• 2316 READ/WRITE No spec
• 2317 READ/WRITE Buffer over
• 2318 READ/WRITE Device No.
• 2319 READ/WRITE Data
• 2320 READ communication error
• 2321 WRITE communication error
• 2322 GET/PUT No spec.
• 2323 GET/PUT Buffer over
• 2324 GET/PUT Number of digits
• 2325 GET/PUT Variable designation
• 2326 GET Numerical data
• 2327 Calculation function no spec.
• 2328 Sub-program no spec.
• 2329 Sub-spindle interference distance
• 2330 Input/output variable no spec.
• 2331 Multiple machining no spec.
• 2332 Sub-spindle no spec.
• 2334 In-process gauging no spec.
• 2335 Post-process gauging no spec.
• 2336 Animation no spec.
• 2337 Graphic backup data file write failure
• 2338 Spindle orientation no spec.
• 2339 Load monitor no spec.
• 2340 Thread phase matching no spec.
• 2341 Circular thread cutting no spec.
• 2342 Circular thread cutting command
• 2343 Tool retract no spec.
• 2344 Tool retract interrupt enable com.
• 2345 Tool retract interrupt disable com.
• 2346 Tool retract interrupt return com.
• 2347 ROBOT no spec.
• 2348 ROBOT program name
• 2349 LOADER no spec.
• 2350 LOADER program name
• 2351 Coupling device program select no spec.
• 2353 CHAMFERING G01 mode
• 2354 CHAMFERING L over
• 2355 CHAMFERING L illegal order
• 2356 CHAMFERING X, Z illegal order
• 2357 CHAMFERING Any angle calculation
• 2358 CHAMFERING Any angle
• 2359 NOSE-R COMP. No spec.
• 2360 NOSE-R COMP. NOSE-R > circle-R
• 2361 NOSE-R COMP. Calculation
• 2362 NOSE-R COMP. Cancel G00 G01
• 2363 NOSE-R COMP. No cross point
• 2364 NOSE-R COMP. Entrance command error
• 2365 NOSE-R COMP. Thread cutting cycle
• 2366 TOOL RADIUS COMP. No spec.
• 2367 TOOL RADIUS COMP. NOSE-R comp. surface change
• 2368 TOOL RADIUS COMP. C-axis separation
• 2369 TOOL RADIUS COMP. QA command
• 2370 TOW-ALONG TAILSTOCK MOVEMENT no spec.
• 2371 TOW-ALONG TAILSTOCK MOVEMENT condition
• 2372 LASER MEASUREMENT no spec.
• 2373 LASER MEASUREMENT condition
• 2374 LAP No spec.
• 2375 LAP B illegal order
• 2376 LAP D illegal order
• 2377 LAP DA(DB) illegal order
• 2378 LAP H illegal order
• 2379 LAP H-U(W) < D (M73)
• 2380 LAP U(W) illegal order
• 2381 LAP U(W) > H
• 2382 LAP XA(ZA), XB(ZB) illegal order
• 2383 LAP Calculation error
• 2384 LAP Down step number over
• 2385 LAP Entry in LAP
• 2386 LAP Sequence name
• 2387 Unable to LAP Control
• 2388 LAP No G-code
• 2389 LAP NOSE-R comp. cancel
• 2390 LAP Entry in NOSE-R comp.
• 2391 LAP Shape designation
• 2392 MULTI CYCLE B illegal order
• 2393 MULTI CYCLE D illegal order
• 2394 MULTI CYCLE F illegal order
• 2395 MULTI CYCLE H illegal order
• 2396 MULTI CYCLE H-U(W) < D (M73)
• 2397 MULTI CYCLE I,K over
• 2398 MULTI CYCLE I,K illegal order
• 2399 MULTI CYCLE L illegal order
• 2400 MULTI CYCLE Entry in LAP
• 2401 MULTI CYCLE U(W) illegal order
• 2402 MULTI CYCLE U(W) > H
• 2403 MULTI CYCLE X,Z illegal order
• 2404 MULTI CYCLE Angle
• 2405 MULTI CYCLE Tool offset
• 2406 MULTI CYCLE Cycle start point
• 2407 MULTI CYCLE Entry in NOSE-R comp.
• 2408 MULTI CYCLE Width
• 2409 TOOL LIFE CONTROL no spec.
• 2410 Tool life management No spare tool
• 2411 TOOL LIFE CONTROL tool group
• 2412 TOOL LIFE CONTROL no T-entry
• 2413 TOOL LIFE CONTROL tool offset group
• 2414 TOOL LIFE CONTROL no T-offset
• 2415 MULTI-MACHINING CYCLE No spec.
• 2416 MULTI-MACHINING CYCLE C
• 2417 MULTI-MACHINING CYCLE I,K
• 2418 MULTI-MACHINING CYCLE Q
• 2419 MULTI-MACHINING CYCLE F
• 2420 MULTI-MACHINING CYCLE L
• 2421 MULTI-MACHINING CYCLE D
• 2422 MULTI-MACHINING CYCLE X,Z
• 2423 MULTI-MACHINING CYCLE SA
• 2424 MULTI-MACHINING CYCLE Feed G94
• 2425 MULTI-MACHINING CYCLE A
• 2426 MULTI-MACHINING CYCLE Thread cycle
• 2427 MULTI-MACHINING CYCLE U,W
• 2428 MULTI-MACHINING CYCLE SB
• 2429 MULTI-MACHINING CYCLE Y-axis mode
• 2430 ATC no spec.
• 2431 ATC syntax
• 2432 ATC TC
• 2434 ATC TL
• 2435 ATC MT
• 2436 ATC MG
• 2438 Unable to M06/M228 command
• 2440 Y-axis no spec.
• 2441 2 saddle machine no spec.
• 2444 Carrier axis variable limit over
• 2445 3-D coordinate conversion
• 2452 Chuck barrier area
• 2453 Tailstock barrier area
• 2456 W-axis minus variable limit over
• 2457 X-axis correction stroke end over
• 2459 Restart axis position is illegal
• 2460 Change timing G13/G14
• 2462 Change timing G122/G123
• 2463 Change timing G140/G141/G142
• 2464 Spindle/turret G-code
• 2465 G122/G123 command mismatch
• 2466 Unable to issue M100 command during Nose-R comp.
• 2472 Y-axis control mode
• 2475 W-axis command G-code
• 2476 Mirror image coordinate selection
• 2477 Sub-spindle mode
• 2478 No workpiece coordinate mode command
• 2479 Contour generation calculation error
• 2480 G132/G133 command error
• 2486 NC turret no spec.
• 2487 Unable to select coordinates
• 2488 UNUSABLE X-axis command
• 2489 NC tailstock parameter error
• 2490 Chuck pressure out of range
• 2491 Horizon barrier intrusion
• 2492 Interrupt program: illegal command
• 2493 Linked external equipment program selection
• 2494 Chuck pressure command illegal
• 2495 Inverse time feed command format
• 2496 CAM data cannot be transmitted.
• 2497 T code
• 2498 Learning cannot be executed.
• 2499 Spindle marker latch data error
• 2500 MULTI-MACHINING CYCLE HS,HI,HJ,HK
• 2501 Recovering synchronous error
• 2502 Block Delete command error
• 2503 End sequence name error
• 2504 PREMIUM THREAD Command error
• 2505 CAM machine no spec.
• 2506 Tool center point control not possible
• 2507 CHP command error
• 2508 Machining mode command format
• 2509 MULTI-MACHINING CYCLE Return point
• 2510 Mistake in torque skip cycle command
• 2511 Remote buffer operation
• 2512 M-tool spindle overload
• 2513 Coordinate calculation
• 2514 MULTI CYCLE C-axis shift
• 2515 Remote buffer operation time out
• 2516 Remote buffer operation communication error
• 2517 W-axis control mode
• 2518 Synchronized tapping command
• 2519 Tailstock control command
• 2520 Mistake in TP command
• 2521 Mistake in BT command
• 2522 Mistake in BA command
• 2523 Thermistor error
• 2524 Mistake in AT command
• 2525 Chuck coordinate change condition
• 2528 Program selection unsuitable
• 2529 Thermal deviation compensation
• 2530 Machining process instruction no.
• 2531 Mirror turning mode
• 2532 System variable set condition error
• 2533 Steady rest over interference pos.
• 2534 LBB turret rotation impossible
• 2536 Coordinate movement rotation copy
• 2537 SLANT PROCESS MODE
• 2538 Incorrect system variable
• 2539 Mistake in B command
• 2541 PROGRAM PRINT command
• 2542 Feed axis retract function command
• 2543 Turret index error position
• 2544 TOOL-ID TOOL DATA
• 2545 MULTI-MACHINING CYCLE LD
• 2546 MULTI-MACHINING CYCLE LK
• 2547 No decimal point
• 2548 X-, Z-axis synchronized feed mode
• 2549 Tool no. mismatch after ATC sequence restart
• 2550 Home position no spec.
• 2551 External home position command
• 2552 Barrier area
• 2555 Linear guide cover interference area command
• 2557 Illegal steady rest command
• 2558 Turning position selection
• 2559 Attachment rotation not possible
• 2561 Illegal system command variable
• 2562 Tool posture fluctuation reduction
• 2563 Mistake in TE command
• 2564 Index disable position
• 2565 Load monitor system variable
• 2566 MULTI-MACHINING CYCLE No M-tool cycle command
• 2567 No helical cutting specifications
• 2568 Mistake in OF command
• 2569 Thermal deviation comp. backup failure
• 2570 W-axis position condition
• 2571 W-axis position no spec.
• 2572 Mistake in RC command
• 2573 Taper cutting cycle
• 2575 Mistake in ‘TD’,’TDG’,’OS’ commands
• 2576 Mistake in H command
• 2577 No axis movement command
• 2578 NO D COMMAND
• 2579 NO L COMMAND
• 2580 Mistake in XS command
• 2581 CAM data deployment mode
• 2582 CAM data file write protect
• 2583 Compensation value overflow
• 2584 CON speed XS-axis
• 2585 XS-axis command turret mode
• 2586 Synchronous mode execution impossible
• 2587 No A command
• 2588 Mistake in OF command
• 2589 Definition conditions
• 2590 Y-axis command
• 2591 Mistake in point command
• 2592 Transport barrier entry command
• 2593 Mistake in CF command
• 2594 Mistake in RJ command
• 2595 Synchronized rotation speed over
• 2596 Synchronized tap overload
• 2597 G15 command
• 2598 No Spec code. “Tool information management spec”
• 2599 Command not possible while mounting LBB.
• 2600 LAW-V machine no spec.
• 2601 Unable to issue T/TE command simultaneously
• 2602 SCHEDULE PROGRAM main program load
• 2603 Spindle rotation fluctuation control no spec.
• 2604 Tow-along steady rest no spec.
• 2605 Tow-along tailstock no spec.
• 2606 READ/WRITE file open
• 2607 Mistake in AP command
• 2608 Mistake in ON command
• 2609 A-axis control no spec.
• 2610 Zero offset select inpossible
• 2611 Spindle fluctuation control no spec.
• 2612 Mistake in TR command
• 2613 Mistake in MTM command
• 2614 Mistake in MTS command
• 2615 Mistake in MGS command
• 2616 B-axis mode
• 2617 Zero setting condition
• 2618 Workpiece detection sensor not ready
• 2619 Mistake in SW command
• 2622 Unset system variable read
• 2623 B-axis no spec.
• 2624 Tow-along steady rest type-B no spec
• 2625 Tow-along steady rest movement condition
• 2626 W-axis overlap
• 2628 Mistake in TW command
• 2629 Mistake in FW command
• 2630 Mistake in SC command
• 2631 DNC-DT Path name
• 2632 DNC-DT Program select
• 2633 DNC-DT Preload error
• 2634 DNC-DT Delete error
• 2635 Y-axis mode
• 2637 No axis movement command
• 2638 A/B saddle synchronized motion command
• 2639 Unable to issue C-axis command during helical cutting
• 2640 AC thread rotation count error
• 2641 AC thread fluctuation control not possible
• 2642 READ/WRITE No empty SAT
• 2643 READ/WRITE File open
• 2644 Unusable PRINT request
• 2645 YS-axis position
• 2646 SYSTEM VARIABLE C-axis separation
• 2648 MG tool ready cycle no spec.
• 2649 SYSTEM VARIABLE Y-axis mode
• 2650 SYSTEM VARIABLE B-axis mode
• 2651 C-axis multi rotation mode
• 2652 Mistake in HA command
• 2653 Mistake in MN command
• 2654 Hob circular cutting command
• 2655 Hob cutting command
• 2657 SYSTEM VARIABLE C-axis connect
• 2658 B-axis independent encoder error
• 2659 NC tailstock position error
• 2662 NC TAILSTOCK no spec.
• 2663 Turning cut condition interlock
• 2667 X-axis mirror image coordinates selected
• 2668 X-axis mirror image coordinates impossible
• 2671 C-axis sync control no spec.
• 2672 C-axis sync command format
• 2674 Default status macro cannot be executed
• 2675 Tool posture command error
• 2676 Tool posture command angle conversion error
• 2677 Attachment change not possible
• 2678 SPM contour control not possible
• 2679 Mistake in Q command
• 2682 Magnetic encoder speed detection error
• 2683 MCS Rotary encoder 5 initialization failure
• 2684 MCS Rotary encoder 5 error
• 2685 MCS Rotary encoder 4 initialization failure
• 2686 MCS Rotary encoder 4 error
• 2687 MCS Rotary encoder 3 initialization failure
• 2688 MCS Rotary encoder 3 error
• 2689 MCS Rotary encoder 2 error
• 2690 MCS Rotary encoder 1 initialization failure
• 2691 MCS Rotary encoder 1 error
• 2692 MCS Linear scale 4 initialization failure
• 2693 MCS Linear scale 4 error
• 2694 MCS Linear scale 3 initialization failure
• 2695 MCS Linear scale 3 error
• 2696 MCS Linear scale 2 initialization failure
• 2697 MCS Linear scale 2 error
• 2698 MCS Linear scale 1 initialization failure
• 2699 MCS Linear scale 1 error
• 2700 No workpiece confirmation error
• 2701 Sequencer Error
• 2702 Spindle command during C-axis connection
• 2703 Chucking miss
• 2704 Chucking miss air off order impossible
• 2705 Tailstock quill over advance
• 2706 Polygon cutting command condition
• 2707 Invalid command during polygon cutting
• 2708 Invalid rotation tool gear
• 2709 Sub-spindle synchronization interlock
• 2710 Sub-spindle synchronization cutting
• 2711 Door open
• 2712 ATC no spec.
• 2713 Invalid ATC syntax
• 2714 Invalid ATC TC no.
• 2716 Invalid ATC TL no.
• 2717 Invalid ATC MT no.
• 2718 Invalid ATC MG no.
• 2719 Invalid ATC command
• 2720 M06/M228 interlock
• 2721 Turret number mismatch
• 2722 Robot/Loader request illegal
• 2723 ATC next tool preparation interlock
• 2724 Invalid ATC sub arm
• 2725 Invalid RS tool L/M
• 2726 Magazine encoder read
• 2727 Magazine rotation interlock
• 2728 Invalid magazine tool no.
• 2729 No magazine return pot
• 2730 Tool insertion interlock
• 2732 Tailstock sleeve position data error
• 2733 Coolant flow
• 2734 Coolant level
• 2735 Spindle low rotation command
• 2736 SVP time constant switching no spec.
• 2737 Invalid tailstock switch position
• 2738 Synchronous hobbing interlock
• 2739 Invalid synchronous hobbing mode
• 2740 Incorrect magazine tool data
• 2741 Touch setter unlock time over
• 2742 Setup switch ON
• 2743 Irregular coolant level
• 2744 Tool breakage
• 2745 Low high-pressure coolant pressure
• 2746 Hydraulic oil unit error
• 2747 Index disable position
• 2748 CPU fan stop
• 2749 Hydraulic oil level lower limit
• 2750 Tool monitoring unit error detection
• 2751 Coolant/Oil mist command
• 2752 Air pressure
• 2753 Unable to change tool
• 2754 Invalid coolant command
• 2755 Semi-dry unit error
• 2756 Actual tool data setting
• 2757 Oil mist unit error
• 2758 Invalid position data
• 2759 Coolant discharge error
• 2760 Sub-spindle rotation tool interlock
• 2761 W-axis overlap mode
• 2762 Chucking miss
• 2763 Coolant filter
• 2764 Coolant error
• 2765 Chip conveyer filter clogged
• 2766 Invalid M-tool spindle command
• 2767 M-spindle low rotation interlock
• 2768 Program check mode interlock
• 2769 Invalid spindle control command
• 2770 SVP time constant switching command
• 2771 APC clamp confirmation
• 2772 APC system mode
• 2773 APC M command
• 2774 Thread cutting cycle interlock
• 2775 Sensor head interlock
• 2776 M command not completed
• 2777 Cross rail positioning sensor error
• 2778 Cross rail motor overload
• 2779 Axis lube motor overload
• 2780 Axis lube pressure ON confirmation
• 2781 No AT command
• 2782 Axis lube pressure OFF confirmation
• 2783 Oil hole motor overload
• 2784 Invalid MT command
• 2785 Invalid AT command
• 2786 No S command
• 2787 No SB command
• 2788 Invalid SB command
• 2789 Coolant tank filter clogged
• 2790 Shower coolant motor overload
• 2791 M spindle head cooling unit
• 2792 Invalid RH command
• 2793 Incorrect attachment index position
• 2794 Mist air lube unit
• 2795 Warming up error
• 2796 Sequence restart
• 2797 Axis interlock release
• 2798 Invalid BC command
• 2800 Alarm detected from externally connected device
• 2801 Turret rotation interlock
• 2802 Invalid long boring bar command
• 2803 ATC tool data setting
• 2804 Attachment control
• 2805 Limit confirmation impossible
• 2806 Door interlock
• 2807 Invalid M code
• 2848 Chip conveyer overload
• 2849 Sensor unit in interference range
• 2850 External request interlock
• 2851 Machine change M-code
• 2852 Hand open/close interlock
• 2853 Teaching operation interlock
• 2854 Machine linked M-code
• 2855 Coolant filter
• 2856 Coolant motor overload
• 2857 UNUSABLE M-code
• 2858 Hand slide advance interlock
• 2887 Coupling device interlock
• 2888 Lube tank level
• 2890 Workpiece clamp miss
• 2891 Tailstock air miss
• 2892 Unable to execute air shut-off command
• 2893 Hydraulic oil controller faulty
• 2894 Spindle lubricant controller error
• 2895 Coolant controller error
• 2896 No touch setter
• 2897 Unloader no spec.
• 2898 Unloader interference position
• 2899 Gauge error
• 2900 DIRECTION V variable
• 2901 DIRECTION Check address
• 2902 DIRECTION Data operation
• 2903 DIRECTION Character use
• 2904 DIRECTION Numerical data
• 2905 DIRECTION Parameter/point
• 2906 DIRECTION Register
• 2907 DIRECTION F
• 2908 DIRECTION E
• 2909 DIRECTION Sequence no.
• 2910 UNUSABLE G-code
• 2911 UNUSABLE M-code
• 2912 UNUSABLE Address character
• 2913 UNUSABLE Mnemonic
• 2914 UNUSABLE Left side direction
• 2915 EXPRESSION Calculation
• 2916 EXPRESSION Syntax
• 2917 EXPRESSION Right side
• 2918 EXPRESSION Left side
• 2919 EXPRESSION Buffer over
• 2920 VARIABLE Buffer over
• 2921 PROGRAM DIRECT Program name
• 2922 PROGRAM DIRECT V variable
• 2923 PROGRAM DIRECT Character use
• 2924 PROGRAM DIRECT G-code
• 2925 BRANCH Sequence name
• 2926 BRANCH Condition
• 2927 Parameter setting illegal
• 2928 Parameter playback impossible
• 2929 Register setting impossible
• 2930 Program plus var. limit over
• 2931 Program minus var. limit over
• 2932 Program request illegal
• 2933 Program request impossible
• 2934 Program external request impossible
• 2935 No program selection
• 2936 No program
• 2937 Program end code
• 2938 Program analysis complete
• 2939 SUB PROGRAM stack
• 2940 SUB PROGRAM Program name
• 2941 SUB PROGRAM Buffer over
• 2942 Command impossible while running
• 2943 Data file read
• 2944 Comment end code not found
• 2945 Equal does not exist
• 2946 No spec.
• 2948 DIRECTION Y
• 2949 DIRECTION Z
• 2950 DIRECTION D
• 2951 DIRECTION L
• 2952 DIRECTION SU
• 2953 DIRECTION Torque limit
• 2954 PROGRAM DIRECT M-code
• 2955 PROGRAM DIRECT Equal
• 2956 Machine change M-code
• 2957 G22 feed
• 2958 Main sequence
• 2959 Barrier limit
• 2960 User reserve code
• 2961 Calculation function no spec.
• 2962 Subscript function no spec.
• 2964 NC program selection
• 2965 EXPRESSION subscript
• 2966 M code time over
• 2967 Cycle time over
• 2968 Program selection
• 2969 G23 FEED
• 2970 DIRECTION X
• 2971 DIRECTION I
• 2972 DIRECTION J
• 2973 DIRECTION K
• 2974 PROGRAM DIRECT hexadecimal data
• 2975 PROGRAM DIRECT character string
• 2976 Stopper position data illegal
• 2977 Program selection unsuitable
• 2978 DIRECTION V
• 2979 DIRECTION C
• 2980 No decimal point
• 2981 DIRECTION Q
• 2982 Time over

Lỗi máy CNC Okuma Alarm C List

Sau đây là liệt kê danh sách Lỗi máy CNC Okuma Alarm C List  for Okuma OSP-P300S/P300L CNC systems.

• 3055 Device temperature too high
• 3056 Non-functioning device detected
• 3057 Unable to start during virus scan
• 3120 Overload detected.
• 3122 Maintenance (by user) necessary
• 3132 VDU communication error
• 3133 VDU detected error
• 3134 VDU initialization failure
• 3135 MCS DD encoder link error
• 3136 MCS DD Encoder error
• 3137 MCS DD Encoder (slave sensor) error
• 3138 MCS DD encoder initialization failure
• 3139 MCS DD encoder (slave sensor) initialization failure
• 3144 MCS Power supply unit overload
• 3150 MCS Undefined alarm number
• 3151 MCS Inverter unit fault
• 3152 Mistake in data from MCS to NC
• 3153 MCS CON APA deviation
• 3154 MCS Power supply unit error
• 3155 MCS Converter link error
• 3156 MCS DC-bus voltage alarm
• 3157 MCS Motor overcurrent
• 3158 MCS Power unit overheat
• 3159 MCS Power unit overload
• 3160 MCS Supply voltage flutter
• 3161 MCS Inverter capacity differs from spec.
• 3162 MCS Winding change failure
• 3163 MCS Encoder link error
• 3164 MCS Encoder detected error.
• 3165 MCS Encoder initialization failure
• 3166 MCS Encoder with shaft detected error
• 3167 MCS Encoder with shaft initialization failure
• 3168 MCS ABSO SCALE error
• 3169 MCS ABSO SCALE initialization failure
• 3170 MCS Magnetic encoder alarm
• 3171 MCS Resolver alarm
• 3172 MCS Pulse generator count over
• 3173 MCS Motor overheat
• 3174 MCS Servo link error
• 3175 MCS Servo link disconnection
• 3176 Mistake in data from NC to MCS
• 3177 MCS Servo data error
• 3178 MCS Illegal command
• 3179 MCS CON speed over
• 3180 MCS Speed command over
• 3181 MCS DIFF over
• 3182 MCS APA speed over
• 3183 MCS Full-closed APA error
• 3184 MCS Over speed
• 3185 MCS Speed deviation over
• 3186 MCS Collision detected
• 3187 MCS Urgent-stop time over
• 3188 MCS Belt is broken
• 3189 MCS Axis change control error
• 3190 MCS Independent encoder initialization failure
• 3191 MCS Calculated current position lies outside range
• 3192 MCS Motor overload
• 3194 MCS ABSO SCALE sub-slider detected error
• 3195 MCS Tandem control communication error
• 3196 MCS Full abso scale link error
• 3197 MCS Full abso scale error
• 3198 MCS Full abso scale initialization failure
• 3199 MCS Axis stop signal error
• 3202 User reserve code
• 3203 Warm up run
• 3204 Running time over
• 3205 Work counter over
• 3206 Cycle time over
• 3207 DNC Start conditions
• 3208 DNC Initialization sequence impossible
• 3209 DNC Illegal text from host
• 3210 DNC Incorrect machine No.
• 3211 DNC Text format error
• 3212 DNC Text receipt error
• 3213 DNC Text transmission error
• 3214 FMS Coupling mode change
• 3215 FMS HOST CPU alarm
• 3216 FMS Operation mode select
• 3217 DNC-B buffer operation
• 3218 DNC-B buffer operation change
• 3226 Common unit illegal
• 3231 Program select
• 3232 Load monitor overload
• 3238 ROBOT alarm/reset
• 3240 LOADER alarm/reset
• 3241 Post-process gauging Unable to transmit
• 3242 Post-process gauging Unable to receive
• 3243 Post-process gauging Time out
• 3244 Post-process gauging Data format error
• 3245 Gauging data out
• 3246 CEJ MATIC Data NG
• 3247 CEJ MATIC Data read
• 3248 Size catcher Data NG
• 3249 Size catcher Gauging error
• 3250 Size catcher Unable to transmit
• 3251 Size catcher Unable to receive
• 3252 Size catcher Time out
• 3253 Size catcher Data format error
• 3254 Schedule program start
• 3255 Main program start
• 3261 Tool life management No spare tool.
• 3264 RS-232C communication illegal
• 3266 Workpiece counter full count
• 3271 Gauging sensor battery change
• 3279 DNC Machining start conditions
• 3280 DNC Data receipt start conditions
• 3289 Load monitor low load
• 3295 Quality check alarm
• 3300 Tool data output
• 3314 External tool offset input
• 3316 Position encoder adjustment required.
• 3319 DNC Ethernet receipt command not allowed.
• 3320 DNC Ethernet receipt error
• 3321 DNC Ethernet transmission error
• 3331 NC tailstock position error
• 3332 Reboot machine.
• 3682 Magnetic encoder speed detection error
• 3683 MCS Rotary encoder 5 initialization failure
• 3684 MCS Rotary encoder 5 error
• 3685 MCS Rotary encoder 4 initialization failure
• 3686 MCS Rotary encoder 4 error
• 3687 MCS Rotary encoder 3 initialization failure
• 3688 MCS Rotary encoder 3 error
• 3689 MCS Rotary encoder 2 error
• 3690 MCS Rotary encoder 1 initialization failure
• 3691 MCS Rotary encoder 1 error
• 3692 MCS Linear scale 4 initialization failure
• 3693 MCS Linear scale 4 error
• 3694 MCS Linear scale 3 initialization failure
• 3695 MCS Linear scale 3 error
• 3696 MCS Linear scale 2 initialization failure
• 3697 MCS Linear scale 2 error
• 3698 MCS Linear scale 1 initialization failure
• 3699 MCS Linear scale 1 error
• 3700 Power save ON
• 3701 CPU temperature
• 3702 Warm up run
• 3703 Oil filter
• 3704 Lube tank flow
• 3705 Lube tank level
• 3706 Spindle lube pressure
• 3707 Spindle cooler error
• 3708 Oil cooler error
• 3709 Coolant level
• 3710 Air blow pressure
• 3711 Air pressure
• 3712 Program selection interlock
• 3713 Chip conveyer overload
• 3714 ZA-axis overload
• 3715 ZB-axis overload
• 3716 XA-axis overload
• 3717 XB-axis overload
• 3718 Coupling device error
• 3719 ROBOT control
• 3720 ROBOT alarm/reset
• 3721 ROBOT/LOADER control
• 3722 LOADER alarm/reset
• 3723 Schedule program start
• 3724 Main program start
• 3725 CEJ MATIC data NG
• 3726 CEJ MATIC data read
• 3727 Auto power off impossible
• 3728 Oil cooler level
• 3729 Coolant error
• 3730 Coolant flow
• 3731 Coolant abnormal
• 3732 Robot/loader axis safety speed over
• 3733 Robot/loader safety speed monitor error
• 3734 ATC step time over
• 3735 Next tool preparation impossible
• 3736 Coolant filter
• 3737 Mist collector
• 3738 Mode switch operation prohibited
• 3739 Control box air conditioner error
• 3740 Air filter clogged
• 3741 Index chuck oil level
• 3742 ATC-axis circuit breaker
• 3743 ATC-axis motor overload
• 3744 Chucking miss air
• 3745 Mist lubrication unit
• 3746 External start switch
• 3747 NC start button
• 3748 Door sensor
• 3749 Automatic lubrication system error
• 3750 Tailstock absolute encoder error
• 3751 Invalid external tool offset input
• 3752 Coolant supply
• 3753 Drain tank
• 3754 Mist collector
• 3755 Workpiece conveyor error
• 3756 Unmachined workpiece detection
• 3757 Bar feeder error
• 3758 Oil mist error
• 3759 Tool monitoring unit error detection
• 3760 Fan cooling unit pressure
• 3761 TOOL change not possible
• 3762 ACC step time over
• 3763 Switch disabled
• 3764 Oil controller unit
• 3765 Spindle vibration sensor
• 3766 Coupling device interlock
• 3767 Tailstock holding miss check air
• 3768 Irregular coolant level
• 3769 Side cover open
• 3770 Safety door open
• 3771 Lube tank motor run time over
• 3772 Coolant flow
• 3773 Earthquake detected
• 3774 EC circuit breaker
• 3775 Lubrication unit error
• 3777 Air blow flow
• 3778 M axis cooling fan overload
• 3779 APC system conditions
• 3780 Touch setter unit error
• 3781 EC overload
• 3782 Sensor contact signal error
• 3783 ATC interlock
• 3784 Fire extinguish unit power OFF
• 3785 Spindle lubrication unit
• 3786 Chip flush-out motor overload
• 3787 M-axis unit command mismatch
• 3788 AAC system condition
• 3789 Air dryer unit error
• 3790 Ext. program select parity check
• 3791 Mist air lubrication unit
• 3792 Chucking miss
• 3793 Coolant level low
• 3794 Power source unit overload
• 3795 Hydraulic oil unit
• 3796 RSS unit battery error
• 3797 RSS unit communication error
• 3798 Unloader interlock
• 3800 Transfer data error
• 3843 Safety fence open
• 3844 Invalid loader grease lubrication input
• 3845 Coolant level lower limit
• 3846 M/C panel at interfering position
• 3847 Invalid limit/proximity switch
• 3848 Anti-gouge unit faulty
• 3849 Tool counter full count
• 3850 External alarm
• 3851 Tool counter faulty
• 3852 Tail stock chuck position
• 3853 Invalid loader limit/proximity switch
• 3854 Chip conveyor stop
• 3855 Oil air unit oil level low
• 3856 Coolant motor overload
• 3857 Oil skimmer overload
• 3858 Chuck grip confirmation unit faulty
• 3859 Fire extinguisher error
• 3860 Fire extinguisher power OFF or error
• 3861 Chip conveyer filter clogged
• 3862 Filtration unit error
• 3874 Sub chip conveyor error
• 3875 Absolute encoder controller error
• 3876 Workpiece loading unit stop signal ON
• 3877 Workpiece counter full count
• 3878 Concentrated chip conveyor
• 3879 Gauging NG
• 3880 Spindle air purge pressure
• 3881 Turnover cycle time over
• 3882 Start impossible
• 3883 Chip crusher error
• 3884 Workpiece puller operation incomplete
• 3885 No workpiece
• 3886 Workpiece present
• 3887 Temperature control unit error
• 3888 Chip conveyor faulty
• 3889 EExternal start signal ON
• 3890 Low level in oil tank
• 3891 Multi-counter tool life
• 3892 Hydraulic oil level lower limit
• 3893 Hydraulic unit oil controller
• 3894 Spindle lubrication controller error
• 3895 Coolant controller error
• 3896 Tool change count-up
• 3897 Workpiece stocker full
• 3898 Cooler error
• 3900 User reserve code
• 3901 External

Lỗi máy CNC Okuma Alarm D List

Sau đây là liệt kê danh sách Lỗi máy CNC Okuma Alarm D List  for Okuma OSP-P300S/P300L CNC systems.

• 4035 Replace memory board battery
• 4036 Key-code data receipt error
• 4037 CCP-CPU error
• 4052 PLC backup data file write
• 4054 ACP key-code data receipt error
• 4055 Safety speed clamping
• 4056 Adjusting Type-J encoder
• 4057 Battery life
• 4058 Previous backup error
• 4059 Backup file error
• 4060 AlarmService internal error
• 4061 UPS Service error
• 4062 Remote Diagnosis error
• 4063 DNC2 communication error
• 4064 Awaiting establishment of DeviceNet
• 4065 FL-net transmission error
• 4066 FL-net transmission failure
• 4067 Maintenance necessary
• 4068 Non-responsive software detected
• 4069 Turret index sequence has not ended.
• 4070 Solid model position error
• 4071 CAS environment file cannot be changed
• 4072 Turret position error
• 4076 CAS software calculation error
• 4077 Turning interlock of CAS
• 4078 Error occurred during CAS
• 4080 Collision Avoidance Function OFF
• 4081 In-position/droop check waiting status
• 4083 Windows updated. Reboot
• 4084 Virus has been detected.
• 4085 Fan motor error at panel computer unit
• 4086 UPS not functioning
• 4087 Non-functioning device detected
• 4088 Virus Detect Function active
• 4090 Machine relocation detected
• 4091 Var. lost motion cannot be applied.
• 4092 MCS Parameter learning
• 4100 Collision avoidance position
• 4101 CAS software environment being changed
• 4102 Awaiting CAS software process
• 4103 Drawing speed over
• 4104 CAS processing time over
• 4105 Collision block detected
• 4106 Collision Avoidance system OFF
• 4107 Awaiting CAS check result
• 4108 Inaccurate material shape
• 4109 CAS operating in rapid mode
• 4110 Turret collision check not performed
• 4120 Overload detected
• 4121 General overload detection disabled
• 4122 Maintenance (by user) necessary
• 4130 MCS Inertia identification
• 4131 VDU initialization failure
• 4132 VDU communication error
• 4133 VDU error
• 4134 MCS Alarm-D occurred
• 4135 MCS DD encoder link error
• 4136 MCS DD encoder error
• 4137 MCS DD encoder (slave sensor) detected error
• 4138 MCS DD encoder initialization failure
• 4139 MCS DD encoder (slave sensor) initialization failure
• 4141 MCS Push reset button to stop spindle
• 4144 MCS power supply unit overload
• 4145 MCS Drive unit external cooling fan stop
• 4147 MCS Drive unit internal cooling fan stop
• 4148 MCS Power supply unit external cooling fan stop
• 4149 MCS Power supply unit internal cooling fan stop
• 4150 MCS Undefined alarm number
• 4151 MCS Inverter unit fault
• 4152 Mistake in data from MCS to NC
• 4153 MCS CON APA deviation
• 4154 MCS Power supply unit error
• 4155 MCS Converter link error
• 4156 MCS DC-bus voltage alarm
• 4157 MCS Motor overcurrent
• 4158 MCS Power unit overheat
• 4159 MCS Power unit overload
• 4160 MCS Supply voltage flutter
• 4161 MCS Inverter capacity differs from spec.
• 4162 MCS Winding change failure
• 4163 MCS Encoder link error
• 4164 MCS Encoder detected error
• 4165 MCS Encoder initialization failure
• 4166 MCS Encoder with shaft detected error
• 4167 MCS Encoder with shaft initialization failure
• 4168 MCS ABSO SCALE error
• 4169 MCS ABSO SCALE initialization failure
• 4170 MCS Magnetic encoder alarm
• 4171 MCS Resolver alarm
• 4172 MCS Pulse generator count over
• 4173 MCS Motor overheat
• 4174 MCS Servo link error
• 4175 MCS Servo link disconnection
• 4176 Mistake in data from NC to MCS
• 4177 MCS Servo data error
• 4178 MCS Illegal command
• 4179 MCS CON speed over
• 4180 MCS Speed command over
• 4181 MCS DIFF over
• 4182 MCS APA speed over
• 4183 MCS Full-closed APA error
• 4184 MCS Over speed
• 4185 MCS Speed deviation over
• 4186 MCS Collision detected
• 4187 MCS Urgent-stop time over
• 4188 MCS Belt is broken
• 4190 MCS Independent encoder initialization failure
• 4191 MCS Calculated current position lies outside range
• 4192 MCS Motor overload
• 4194 MCS ABSO SCALE sub-slider detected error
• 4195 MCS Tandem control communication error
• 4196 MCS Full abso scale link error
• 4197 MCS Full abso scale error
• 4198 MCS Full abso scale initialization failure
• 4199 MCS Axis stop signal error
• 4200 Reboot enabled parameter set
• 4201 MACHINING MANAGEMENT data backup stop
• 4202 DNC-B Communication system abort
• 4203 DNC-B Communication error
• 4204 DNC-B Message format error
• 4205 H1 turret interference barrier parameter not set
• 4206 SPM Parameter unsuitable
• 4207 Unable to execute Hi-CUT Pro control
• 4208 G265/G264 commands: Unusable address character
• 4209 Hi-CUT Pro parameter out of range (replacing)
• 4210 SPM contour control not possible
• 4211 SPM parameter out of range (replacing)
• 4214 RS232C communication not ready
• 4215 Communication buffer over
• 4216 Communication procedure No response
• 4217 Communication procedure NAK/WACK
• 4218 Communication procedure Illegal text
• 4219 Communication procedure ENQ
• 4220 Communication procedure EOT
• 4221 Communication procedure TTD
• 4223 Motor not ready to start
• 4224 Canceling stroke end limit
• 4225 Pitch compensation data calculation
• 4226 MSB load error
• 4227 External start not possible
• 4228 SSynchronized rotation speed over
• 4230 Torque limit recovery
• 4232 Backup data read/write
• 4237 Magazine operation panel communication error
• 4238 Please open magazine door
• 4240 Tool life management No spare tool
• 4242 Parameter set value incorrect
• 4245 Waiting program selection during program operation.
• 4247 Main spindle max. speed designation
• 4248 DNC NC receipt start conditions
• 4249 Tool life warning
• 4251 Axis feed rate restriction
• 4252 Detector operation check mode
• 4258 Y-axis cancel mode
• 4261 Workpiece counter over
• 4267 PLC link error
• 4268 PLC communication error
• 4269 ROBOT control
• 4274 User reserve code
• 4281 Workpiece counter over
• 4284 Thermistor error
• 4285 Thermal deviation compensation
• 4288 PSC Learn converge protect error
• 4289 Spindle able to enter transportation barrier
• 4290 TCP/IP communication error
• 4291 Position encoder auto adjustment
• 4292 Please check the program
• 4294 Extended Y-axis plus variable limit
• 4295 TDC parameter not set
• 4297 Main Magazine tool Quantity over
• 4298 DNC Ethernet communication error
• 4300 B-axis independent encoder connecting
• 4301 Tail-stock position error
• 4302 Please supply oil of chuck
• 4303 Movement to sizing position stopped
• 4304 No axis movement after offset change
• 4305 Y-axis not at turning position
• 4306 Turret movement decelerating
• 4307 Alarm-A at other system
• 4308 X-axis over limit
• 4309 Clutch A slip monitor OFF
• 4311 Interrupt program
• 4314 Learning required for cam data
• 4315 Permissible value exceeded
• 4316 Manual feed invalid
• 4345 Unable to execute feed axis retract function
• 4346 ZA-W interference parameter not set
• 4347 TDC invalid
• 4348 X-C-axis coordinate value error
• 4349 Mode switching impossible
• 4682 Magnetic encoder speed detection error
• 4683 MCS Rotary encoder 5 initialization failure
• 4684 MCS Rotary encoder 5 error
• 4685 MCS Rotary encoder 4 initialization failure
• 4686 MCS Rotary encoder 4 error
• 4687 MCS Rotary encoder 3 initialization failure
• 4688 MCS Rotary encoder 3 error
• 4689 MCS Rotary encoder 2 error
• 4690 MCS Rotary encoder 1 initialization failure
• 4691 MCS Rotary encoder 1 error
• 4692 MCS Linear scale 4 initialization failure
• 4693 MCS Linear scale 4 error
• 4694 MCS Linear scale 3 initialization failure
• 4695 MCS Linear scale 3 error
• 4696 MCS Linear scale 2 initialization failure
• 4697 MCS Linear scale 2 error
• 4698 MCS Linear scale 1 initialization failure
• 4699 MCS Linear scale 1 error
• 4700 External cycle start interlock
• 4701 Chip conveyer overload
• 4702 Cycle start interlock
• 4703 Canceling stroke end limit
• 4704 Please open door
• 4705 Door interlock all axis stop
• 4706 Canceling door interlock
• 4707 Enabling Switch faulty
• 4708 ATC system mode
• 4709 Power sequence error
• 4710 Parameter non set
• 4711 Spindle motor not ready to start
• 4712 Reboot enabled parameter set
• 4713 Executing power OFF sequence
• 4714 Workpiece counter full count
• 4715 Preparing for warming up
• 4716 Motor not ready to start
• 4717 Dual cycle start button interlock
• 4718 Invalid parameter setting
• 4719 Please open side cover
• 4720 Dual cycle start button interlock
• 4721 Feed rate limitation
• 4722 System check mode
• 4723 Machine enabling button pressed
• 4724 Please open safety fence
• 4725 Please close front door
• 4726 Opposite side front door open
• 4727 Safety fence open
• 4728 Please close other side front door
• 4729 Please open magazin door
• 4730 Magazine door open
• 4731 Multiple safety guards open
• 4732 Gauging sensor power ON
• 4733 Measurement system error
• 4734 Please close safety guards
• 4735 Full of chips
• 4736 Sensor head
• 4737 Other door open
• 4738 Magazine OP panel COMM error
• 4739 Turret not ready to start
• 4740 2nd Spindle control interlock
• 4741 Magazine operation panel manual interrupt
• 4742 Turret encoder offset disabled area
• 4743 Turret index disabled area
• 4744 Turnover cycle
• 4745 REDUCE switch operation error
• 4746 Tool change mode sw operation error
• 4747 Gauging sensor battery change
• 4748 Additional coolant level low
• 4749 Please close door
• 4750 Safety interlock
• 4751 Tailstock quill interlock
• 4752 Tailstock absolute coder error
• 4753 Workpiece hand control
• 4754 Bar stock empty
• 4755 Roof window open interlock
• 4756 Canceling robot/loader and machine interlock
• 4757 Sp. oil air lub. air extraction mode
• 4758 Index chuck adjust mode
• 4760 Moving to home position
• 4761 Override condition
• 4762 Side cover open
• 4763 Home position return interlock
• 4764 Spindle orientation interlock
• 4765 Setup not complete
• 4766 Setup complete interlock
• 4767 ACC safety door locking switch NG
• 4768 Please open ACC safety door
• 4769 ACC system mode
• 4770 Mode switch NG
• 4771 Magnet chuck unclamp cycle
• 4772 Tool select switch mismatch
• 4773 ATC shutter barrier area
• 4774 Invalid zero offset no.
• 4775 Please open spindle cover
• 4776 Canceling interference detection
• 4777 Mist collector power OFF
• 4778 Side cover open
• 4779 ATC shutter interlock cancel mode
• 4780 Maintenance door open
• 4781 Ladder gate open.
• 4782 Workpiece stocker error
• 4783 Workpiece stocker overload
• 4784 Mist collector error
• 4785 Self check counter full count
• 4786 Coolant controller error
• 4787 Manual tool change enabled
• 4788 Chip conveyer stop
• 4789 Sensor overstroke
• 4790 Chucking miss air route clogged
• 4791 Linear guide cover interference
• 4792 Workpiece washer overload
• 4793 Coolant filter
• 4794 Sequencer alarm
• 4795 Please open ceiling door
• 4796 APC safety interlock
• 4797 Please open APC door
• 4798 APC door lock incomplete
• 4800 Tow-along steady rest connection
• 4801 Oil mist error
• 4802 Turret rotation interlock
• 4803 Cross rail positioning auto set mode
• 4804 Workpiece washing gun error
• 4805 Coolant unit error
• 4806 Lube oil drain tank overflow
• 4807 Axis lube level low
• 4808 Coolant level low
• 4809 ATC step time over
• 4810 System check
• 4811 Coolant tank upper level
• 4812 Chip crusher error
• 4813 Waiting for workpiece check
• 4814 Chuck open/close interlock
• 4815 Attachment turret rotating
• 4816 Long boring bar interlock
• 4817 Safety door open interlock
• 4818 Attachment manual change mode
• 4819 ATC door not at end of stroke
• 4820 M-Spindle rotation limit
• 4821 Steady rest interlock
• 4822 Feed axis condition
• 4823 Turret indexing at reduced speed
• 4824 Setup mode
• 4825 Axis position encoder control error
• 4826 General overload detection disabled
• 4827 Canceling chuck grasp interlockl
• 4828 Please switch door interlock ON
• 4829 NC tailstock thrust change interlock
• 4830 Tool indexing not complete
• 4831 Door interlock
• 4844 Coupling device interlock
• 4845 Coolant level warning
• 4846 Unloader setting position parameter
• 4847 Interference area intrusion
• 4848 No lower table present signal
• 4849 Coolant level
• 4850 Safety fence interlock
• 4851 Door interlock
• 4852 Canceling stroke end limit
• 4853 Robot/loader power sequence error
• 4854 Loader interference
• 4855 Front door open interlock
• 4856 Please open safety fence
• 4857 Please close safety fence
• 4858 Feed rate limit
• 4859 Teaching panel enabling switch error
• 4860 Multiple safety guards open
• 4861 Equip. safety fence parameter mismatch
• 4862 Dual cycle start button interlock
• 4863 Tool change count-up
• 4864 Other door open
• 4865 Performing turnover cycle
• 4866 No workpiece
• 4867 M-spindle angle uncertain
• 4868 Cycle start interlock
• 4869 Chuck was changed
• 4870 Invalid servo data selection
• 4871 Inside barrier
• 4872 Tailstock fretting
• 4873 Door open/close limit switch NG
• 4874 XB cover interference
• 4875 Please push the NC start button
• 4876 Please discharge coolant
• 4877 Invalid positioning point
• 4878 Pulse handle mode
• 4879 Curvic cover not attached
• 4880 Measurement unit error
• 4881 NG chute workpiece present
• 4882 Quality check counter notice count
• 4883 Tow-along tailstock unclamp
• 4884 Tool counter full count
• 4885 Quality check counter full count
• 4886 Tool counter warning
• 4887 Tailstock/Chuck Pedal Enable
• 4888 Mode switch operation error
• 4889 PLC link error
• 4890 Dust collector in local mode
• 4891 Chip conveyor in local mode
• 4892 Chip conveyor error
• 4893 OP panel not at retract position
• 4894 Multi-counter tool life warning
• 4895 Hydraulic fluid level low
• 4896 Lubricant level
• 4897 Gauging data ready time out
• 4898 Power save ON
• 4899 Lower turret origin return interlock
• 4900 Motor not ready to start
• 4903 Reboot enabled parameter set
• 4904 Barrier intrusion
• 4905 Safety speed clamping
• 4907 Alarm-A at other system