Lỗi máy cnc doosan mx
Danh sách lỗi Lỗi máy cnc doosan mx
| Alarm No. | Lỗi máy cnc doosan mx |
| 2001 | WHETHER EMERGENCY BUTTON IS PRESSED OR OVERTRAVEL OF AXES IS DETECTED, RELEASE EMERGENCY BUTTON AND LIMIT SWITCH FOR OVERTRAVEL CHECK. |
| 2002 | THE ALARMS OF THE MAIN SPINDLE MOTOR AND SERVO UNIT DETECTED, CHECK ALARM DISPLAY ON THE SERVO UNIT THEN RETRY AFTER POWER OFF-ON. |
| 2003 | OVERCURRENT IN THE CONTROL POWER CIRCUIT, ABNORMALLY LARGE CURRENT FLOW IS DETECTED IN THE CONTROL POWER CIRCUIT, CHECK FOR CONTROL POWER SHORT CIRCUIT. |
| 2004 | HYD. PUMP MOTOR OVERLOAD IS DETECTED, CHECK OVERLOAD VALUE ON THE THERMAL RELAY AND MOTOR. |
| 2005 | HYD. PRESSURE IS DOWN, CHECK HYD. PRESSURE SWITCH, PRESSURE VALUE AND LEAKAGE OF HYDRAULIC. |
| 2007 | SPINDLE ROTATION IS ABNORMAL. Lỗi máy cnc doosan mx |
| 2009 | REVOVING SPINDLE EMERGENCY STOP |
| 2010 | INVERTER FAULT ALARM |
| 2011 | KEEP RELAY SETTING ALARM. PLEASE CHECK THE KEEP RELAY(K5,K5) |
| 2016 | PSM POWER RUNNING ALARM. PLEASE CHECK AUXILLARY CONTACT ON THE MAGNETIC CONTACTOR (KM10 OR KM110). |
| 2019 | MILLING SPINDLE ORIENTATION OVERTIME |
| 2020 | COOLANT & LUB. PUMP MOTOR OVERLOAD OR Q11 FOR SERVO TURRET, CHIP CONVEYOR AND BAR FEEDER OVERLOAD IS DETECTED. |
| 2021 | TORQUE SKIP DATA ERROR Lỗi máy cnc doosan mx |
| 2022 | SPINDLE ORIENTATION CONFIRM IS NOT DETECTED WITHIN 10SEC, CHECK ORIENTATION PARAMETER AND READJUST. ORIENTATION INDEX COMMAND ALARM. |
| 2023 | TOOL INDEX OVERTIME |
| 2024 | TOOL NUMBER COMMAND ALARM |
| 2025 | TOOL NUMBER SELECT KEEP RELAY SET ALARM |
| 2027 | SPINDLE SPEED ARRIVAL IS NOT DETECTED WITHIN 7SEC, CHECK SPINDLE SERVO UNIT. |
| 2028 | SPINDLE ROTATION CONDITION IS NOT READY, CHECK SPINDLE ROTATION CONDITION. |
| 2029 | SPLASH GUARD DOOR IS OPEN, CHECK SPLASH GUARD DOOR OPEN ANDLIMIT SWITCHES. |
| 2030 | M17 OR M18 IS COMMANDED IN ILLEGAL MODE, PLEASE CONFIRM MDI MODE. |
| 2031 | PLEASE MANUAL REF.POINT RETURN, OTHERWISE AUTO.OPERATION IS IMPOSSIBLE. |
| 2032 | FEEDHOLD PUSH BUTTON IS PRESSED. |
| 2033 | AIR OR COOLANT PRESSURE SWITCH IS DOWN. |
| 2034 | PROXIMITY SWITCH FOR CHUCK CLAMP CONFIRM POSITION ERROR, RESET SWITCH POSITION (PX1.M) (PX2.M) |
| 2035 | AXIS CHANGE OVERTIME. Lỗi máy cnc doosan mx |
| 2036 | M68 OR M69, M168 OR M169 IS NOT FINISHED WITHIN 15SEC AFTER COMMAND, CHECK SOLENOID VALVE, POSITION SWITCH AND OPERATION CONDITION. |
| 2037 | M78 OR M79 IS NOT FINISHED, WITHIN 15SEC AFTER COMMAND, CHECK SOLENOID VALVE, POSITION SWITCH AND OPERATION CONDITION. |
| 2038 | M45,M46,M47 IS NOT FINISHED WITHIN 15SEC AFTER COMMAND, CHECK SOLENOID VALVE, POSITION SWITCH AND OPERATION CONDITION. |
| 2039 | M10 OR M11 COMMAND ALARM, CHECK SOLENOID VALVE, POSITION SWITCH AND OPERATION CONDITION. |
| 2040 | M50 OR M51 IS NOT FINISHED, WITHIN 15SEC AFTER COMMAND, CHECK SOLENOID VALVE, POSITION SWITCH AND OPERATION CONDITION. |
| 2041 | THE ALARMS OF THE BARFEEDER IS DETECTED, CHECK BAR-FEEDER. |
| 2042 | M52, M53, M152 OR M153 IS NOT FINISHED, WITHIN 15SEC AFTER COMMAND, CHECK SOLENOID VALVE, POSITION SWITCH AND OPERATION CONDITION. |
| 2043 | M58 OR M59 IS NOT FINISHED, WITHIN 15SEC AFTER COMMAND, CHECK SOLENOID VALVE, POSITION SWITCH, AND OPERATION CONDITION. |
| 2045 | Q-SETTER OPERATION ALARM. CHECK SENSOR AND SOLENOID. TO MEASURE X1-AXIS THAT Y-AXIS SHOULD BE LOCATED AT 0. (1ST.REF) POSITION |
| 2046 | CHUCK IS OPENED DURING THE SPINDLE ROTATION, CHECK HYD.PRESSURE. |
| 2047 | TURRET CLAMP SWITCH ERROR Lỗi máy cnc doosan mx |
| 2048 | THE RESET COMMAND IS USED WHILE PROGRAM IS RUNNING. |
| 2049 | M88,M89,M90,M188,M189,M190 COMMAND ALARM. CHECK SOLENOID VALVE, POSITION SWITCH AND OPERATION CONDITION. |
| 2050 | LUB.PRESSURE IS DOWN OR LUBRICATION OIL LEVEL IS LOW,CHECK LUB.UNIT AND REPLENISH THE OIL. |
| 2051 | OIL COOLER ALARM |
| 2052 | M61 OR M62, M161 OR M162 IS NOT FINISHED WITHIN 15SEC AFTER COMMAND. PLEASE CHECK INITIAL CONDITION. |
| 2053 | WORK EJECTOR & DETECTOR ALARM |
| 2054 | MILLING SPINDLE IS UNCLAMPED.MILLING SPINDLE SHOULD BE CLMAPED IN TURNING MODE. |
| 2055 | ILLEGAL SYNCHRO INITIAL STATE IS DETECTING . PLEASE CHECK CHUCK STATE. |
| 2056 | THIS COMMAND CANNOT BE PERFORMED. PLEASE PERFORM THE REF. POSITION RETURN OF X & Y-AXIS BEFORE THIS COMMAND. |
| 2057 | TOOL LIFE COUNT END ALARM. |
| 2058 | PARTS COUNT END ALARM. Lỗi máy cnc doosan mx |
| 2059 | M,T-CODE COMMAND ALARM WITH A-AXIS. |
| 2060 | CHUCK UNCLAMP STATUS. |
| 2061 | SAFETY LOCKING SWITCH ALARM. PLEASE CHECK CONDITION OF THE LOCKING KEY SWITCH OR WIRE CONDITION THAT IS CONNECTING BETWEEN NO.11 AND NO.12 IN SAFET LOCKING SWITCH. |
| 2062 | LIMIT SWITCH FOR PROGRAMABLE TAILSTOCK IS NOT OPERATED WITHN 5SEC AFTER COMMAND, CHECK SOLENOID VALVES AND LIMIT SWITCHES. |
| 2063 | PROXIMITY SWITCH FOR Q-SETTER IS NOT OPERATED WITHIN 5SEC AFTER COMMAND, CHECK SOLENOID VALVES AND PROXIMITY SWITCHES. |
| 2064 | M66 OR M67 COMMAND ON THE M/C, THE NEXT M03 OR M04 COMMAND. |
| 2065 | Y-AXIS IS NOT IN A REFERENCE POSITION. PLEASE RETURN THE Y-AXIS TO REFERENCE POSITION FOR BT-AXIS MOVING. |
| 2066 | CHECK POSITION DETECTING SWITCHES ARE OPERATED SIMULTANEOUSLY, CHECK SWITCH. |
| 2067 | TOOL SWITCH ALARM |
| 2068 | DRY RUN STATUS. IF YOU PRESS CYCLE START BUTTON, THIS ALARM WILL RESET. |
| 2069 | COOLANT FILTER CHANGE ALARM |
| 2070 | SPINDLE CAMMAND IS ABNORMAL. CHANGE SPINDLE COMMAND AFTER SPINDLE STOP(M05/M35/M65/M105/M165). |
| 2071 | CHIP CONVEYOR ALARM |
| 2072 | TORQUE ALARM |
| 2073 | ILLEGAL COMMAND ALARM |
| 2074 | COOLJET LOW PRESSURE OR FILTER BLOCK ALARM |
| 2075 | TOTAL CYCLE START ALARM |
| 2076 | HIGH PRESSURE FILTER OR COOLJET FILTER BLOCK |
| 2077 | MILLING SPINDLE CLAMP, UNCLAMP COMMAND ALARM. MILLING SPINDLE IS ROTATING OR SENSOR IS ABNORMAL. |
| 2078 | B-AXIS DISC CLAMP COMMAND IS NOT AVAILABLE WHEN NEW TYPE B-AXIS IS USED. |
| 2079 | B-AXIS SENSOR ALARM. PLEASE CHECK THE B-AXIS DISC CLAMP CHECK SENSOR AND CURVIC CLAMP CHECK SENSOR. |
| 2080 | B-AXIS ANGLE IS NOT A MULTIPLE OF 15 DEGREE |
| 2081 | B-AXIS POSITION S/W ALARM |
| 2082 | MILLING SPINDLE IS CLAMPED YET |
| 2083 | MILLING SPINDLE IS UNCLAMPED YET |
| 2084 | IN HANDLE MODE, CAN’T CHANGE TOOL OFFSET WITH Q-SETTER. PLEASE, CHANGE MODE TO JOG MODE AND TRY AGAIN. |
| 2085 | RETURN THE REFERENCE POINT OF X1 AND X2-AXIS FOR MOVING A-AXIS. |
| 2086 | TOOL MONITOR ALARM.DETECT ABNORMAL LOAD AND TOOL WARN ALARM |
| 2087 | TOOL MONITOR ALARM.DETECT ABNORMAL LOAD AND TOOL BROKEN ALARM |
| 2088 | THE SPINDLE SWITCHING IS INVALID IN RIGID TAPPING MODE. CANCEL RIGID TAPPING MODE TO SWITCH OTHER SPINDLE. |
| 2089 | B-AXIS IS NOT CLAMPED YET. PLEASE MAKE SURE THAT THE B-AXIS IS CLAMPED BY M106,M110 OR M112. |
| 2090 | PROGRAM RESTART TOGGLE SWITCH ON STATE. |
| 2091 | SERVO TURRET BATTERY LOW ALARM, PLEASE CHANGE BATTERY IN AMP. MODULE WITHIN 2 WEEKS. |
| 2092 | SPINDLE COMMAND ALARM. WHEN COMPOSITION CONTROL MODE, REV-SPINDLE RECOMMAND IS IMPOSSIBLE AFTER REV-SPINDLE STOP. |
| 2093 | REFERENCE COMMAND FROM REFERENCE POSITION KEEP STATE. |
| 2094 | HIGH LOW CHUCK SWITCHING STATE. OPERATE CHUCK AS UNCLAMPING AND CLAMPING BY FOOT SWTCH. |
| 2095 | RIGID TAPPING OR ORIENTATION COMMAND ALARM. M19 OR M119, M29 IS INVALID ON G96 MODE. PLEASE MODIFY PROGRAM. |
| 2096 | SPINDLE OVERRIDE OR FEEDRATE 0%. |
| 2097 | MACHINE LOCK ON STATUS. |
| 2098 | M00 OR M01 COMMAND. |
| 2099 | M02 OR M30 COMMAND. |
| 2100 | MACHINE IS IN SERVICE MODE. 1)MACHINE WILL OPERATE WITH DOOR OPEN. 2)SPINDLE WILL NOT START UNLESS THE DOOR IS CLOSED.3)TAPPING OR THREADING MAY NOT WORK UNLESS THE DOOR IS |
| 2101 | SPINDLE TOOL UNCLAMP ALARM |
| 2102 | MAIN POWER PHASE ALARM |
| 2103 | M06 OVERTIME ALARM |
| 2104 | T-CODE COMMAND ERROR |
| 2105 | ATC OPERATION COMMAND ERROR |
| 2106 | TOOL POST SEARCH OVERTIME ALARM |
| 2107 | ATC MAGAZINE ROTATION OVERTIME ALARM |
| 2108 | ATC DOOR SWITCH ERROR |
| 2109 | TOOL MAGAZINE SYNCHRO MAL-FUNCTION |
| 2110 | ATC INTERLOCK ALARM |
| 2111 | ATC MAGAZINE GUARD DOOR OPEN |
| 2112 | MAINTENANCE MODE ON STATE |
| 2113 | M149 COMMAND ERROR |
| 2114 | SPINDLE TOOL INTERFERENCE ALARM |
| 2115 | SPINDLE TOOL NO.IS MISMATCHED |
| 2116 | MINI-TURRET 180 COMMAND ALARM. MILLING SPINDLE SHOULD BE ORIENTATED BEFORE COMMAND G400 J12. |
| 2117 | MUST BE ATC 1CYCLE |
| 2118 | ATC OP MANUAL MODE |
| 2119 | SPINDLE AND WAITING TOOL NUMBER IS ZERO. |
| 2120 | SPLASH GUARD DOOR MUST BE OPENED WHEN THE TOOL UNCLAMP OPERATION IS DOING IN MANUAL MODE |
| 2121 | TOOL NUMBER SELECT KEEP RELAY IS NOT SET PROPERLY. |
| 2122 | TOOL CHANGER MOTOR BRAKE RELEASE |
| 2123 | TOOL SEARCH ILLEGAL ALARM |
| 2124 | M06 COMMAND ILLEGAL POSITION |
| 2125 | SPINDLE TOOL CLAMP/UNCLAMP ALARM |
| 2126 | WAITING POT SWITCH ERROR |
| 2127 | CHANGER ARM POSITION CHECK ALARM |
| 2128 | MUST BE COMMAND NEXT TOOL NO. |
| 2129 | ATC OPERATION COMMAND ERROR |
| 2130 | CONSTANT SURFACE COMMAND ALARM.IN COMPOSITION CONTROL MODE, THE CONSTANT SURFACE CONTROL COMMAND FROM LOWER(UPPER) MUST BE COMMANDED AFTER MILLING ROTATING COMMAND |
| 2131 | SPINDLE COMMAND ALARM. AFTER SPINDLE SELECTION, SPINDLE ROTATION COMMAND IS VALID(M05/M35/M105/M135). IF SPINDLE TO SELECT IS ROTATING, MUST BE STOP SPINDLE TO SELECT |
| 2132 | ATFER MAIN POWER OFF/ON, C1 AND C2 AXES MUST BE RETURN REF.POINT BY MANUAL, OTHERWISE AUTO.OPERATION IS IMPOSSIBLE. |
| 2133 | COMPOSITION CONTROL COMMAND ALARM. AFTER SELECT C2-AXIS(M135)FROM UPPER OR C1-AXIS(M35) FROM LOWER, M211 COMMAND IS POSSIBLE. |
| 2134 | TURRET CONTROL UNIT ALARM. CHECK SERVO CONTORL UNIT IN CONTROL CABINET. |
| 2135 | LEFT SPINDLE RIGID TAP IS VALID ONLY FOR THE UPPER PATH AND RIGHT SPINDLE RIGID TAP IS VALID ONLY FOR LOWER PATH |
| 2150 | A-AXIS MOVEMONT IS PROHIBITED IN CHUCKING CLOSED CONDITION |
| 2161 | SPINDLE WARM UP IS REQUESTED. PLEASE RUNNING ALL SPINDLES MORE THAN 15 MINUETES UNDER 1,000RPM |
| 2162 | SPINDLE WARM UP IS COMPLETED |
| 2165 | CHECK HOME POSITION OF EACH UNIT FOR PARTS CATCHER(STOPPER ADV:X64.5, BODY RET:X64.6, BUCKET RET:X65.2, ARM RET:X65.4) |
| 2166 | A-AXIS IS REF.POINT AND Z1,Z2-AIXS IS IN RIGHT POSITION REGION FROM REF.POINT, M310/M311/M256 COMMAND CONDITION :A-AXIS IS REF. POINT AND Z1 AND Z2 AXIS IS IN LEFT POSITION REGION FROM REF. |
| 2167 | CUTTING FEED COMMAND IS COMMANDED WHEN THE B-AXIS IS NOT CLAMPED YET. |
| 2168 | RETURN A-AXIS TO THE REFERENCE POINT FOR MOVING Z2-AXIS OR COMMAND M217 TO RELEASE Z2 AXIS INTERLOCK. |
| 2169 | EXIN DATA READ ALARM. |
| 2170 | IT IS NOT ABLE TO MOVE Z-AXIS WHEN WAITING POT IS NOT IN THEIR HOME POSITION(WAITING POT UP AND HOME POSITION) |
| 2173 | LUBRICATION OIL LEVEL IS LOW. |
| 2174 | TOUCH PROBE UNIT ALARM. BATTERY IS LOW OR SIGNAL LEVEL IS LOW. |
| 2175 | TRANSFERRING WITH FEED FROM THE TURRET UNCLAMP CONDITION WHICH IS IMPOSSIBLE. |
| 2176 | THIS COMMAND CANNOT BE PERFORMED. PLEASE PERFORM THE REF. POSITION RETURN OF C1 & C2-AXIS BEFORE THIS COMMAND. |
| 2177 | TOOL SPINDLE OVERLOAD ALARM, PLEASE CHECK CUTTING CONDITION IN PROGRAM. |
| 2178 | C-AXIS HIGH/LOW CLAMP OR UNCLAMP M-COMMAND CONDITION ALARM. THE M88 OR M89,M90(M188 OR M189,M190) COMMAND OF THE OTHER PATH IS VALID IN COMPOSITION CONTROL STATE. |
| 2179 | LOWER TURRET CAN NOT INDEX OR MOVE TO -Z2 DIRECTION IN INTERFERENCE AREA WITH LEFT SPINDLE. PLEASE MOVE THE Z2-AXIS TO THE RIGHT WHERE THE INTERFERENCE WITH LEFT SPINDLE IS NOT |
| 2180 | X2-AXIS CAN NOT MOVE IN INTERFERENCE AREA WITH LEFT SPINDLE. PLEASE MOVE THE Z2-AXIS TO THE RIGHT WHERE THE INTERFERENCE WITH LEFT SPINDLE IS NOT EXIST. |
| 2181 | KNOLL COOLANT SYSTEM ALARM@0A@ |
| 2182 | Y-AXIS & A-AXIS ARE IN INTERFERENCE AREA. PLEASE CHECK THE INTERFERENCE AREA |
| 2185 | CHECK HOME POSITION OF EACH UNIT FOR PARTS CATCHER(STOPPER ADV:X64.5, BODY RET:XX64.6, BUCKET RET:X65.2, ARM RET:X65.4@0A@) |
| 2186 | WHEN PARTS UNLOADER IS OPERATIING BY M256 COMMAND,THE Z1,Z2-AXIS CAN MOVE ONLY IN THE LEFT POSITION REGION FROM REF.POINT. |
| 2187 | RIGHT SPINDLE ROTATION STATE. PLEASE SPINDLE STOP. |
| 2188 | PROGRAM START M FUNCTION ALARM. PLEASE CHECK M-CODE (M23) |
| 2189 | C-AXIS BRAKE NOT RELEASED, PLEASE CHECK C-AXIS UNCLAMP SOLENOIDE VALVE AND PRESSURE SWITCH. |
| 2190 | PROGRAM RESTART ERROR BY OPTIONAL STOP. MUST BE IN STATE OF UPPER/LOWER UNIT AND MEM MODE TO RESTART PROGRAM STOPPED BY OPTIONAL STOP ON MEM MODE. |
| 2192 | TAIL STOCK INTERLOCK ALARM, PLEASE CHECK THE POSITION OF Z-AXIS AND TAIL STOCK. |
| 2193 | THE PROGRAM NUMBER OF UPPER UNIT AND ONE OF LOWER UNIT ARE NOT SAME. PLEASE CHECK PROGRAM NUMBER OR SET K60.1(CHECK PROGRAM NUMBER) TO 0 |
Kanematsu KGK Vietnam
Kanematsu KGK là một công ty Nhật Bản được thành lập năm 1963. Công ty chuyên về kinh doanh các loại sản phẩm, công cụ như máy CNC, máy tiện cnc, máy ép nhựa, công cụ đo lường… Để mang đến cho khách hàng sự hài lòng an tâm, Kanematsu KGK cũng có các dịch vụ hỗ trợ bao gồm dịch vụ trước khi bán, dịch vụ bảo dưỡng và hỗ trợ kĩ thuật. Ứng dụng bí quyết kĩ thuật và kinh nghiệm tích lũy nhiều năm, Kanematsu KGK xác định sẽ đáp ứng khách hàng qua các giải pháp công nghiệp tối ưu. Để khai thác tiềm năng thị trường Việt Nam, Kanematsu KGK đã đến và lập ra văn phòng đại diện Hà Nội. Với tác phong làm việc chuyên nghiệp, công ty mong muốn đem lại sản phẩm đáp ứng nhu cầu khách hàng.
Các sản phẩm phân phối kinh doanh chính :
- Máy phay CNC
- Máy tiện CNC
- Robot công nghiệp.
- Máy gia công tia lửa điện
- Các loại máy công cụ khác.
- Biến tần công nghiệp
Với đội ngũ quản lý kỹ sư chuyên nghiệp nhiều kinh nghiệm đông đảo kỹ thuật viên công nhân lành nghề Kanematsu KGK Vietnam luôn đáp ứng được đa dạng yêu cầu từ Quý khách hàng với chất lượng tốt nhất.
Chúng tôi luôn luôn nỗ lực cải tiến hoàn thiện hệ thống để mang lại cho khách hàng những sản phẩm và dịch vụ tốt nhất, mục tiêu của chúng tôi luôn luôn lấy sự hài lòng của khách hàng làm nền tảng cho sự phát triển bền vững.
Chúng tôi trân trọng cảm ơn Quý khách hàng đã quan tâm và sử dụng sản phẩm dịch vụ của chúng tôi và mong muốn đồng hành cùng sự phát triển của Quý khách hàng
